Table of Contents
A rule of thumb with springs is that four quarter turns equals a full revolution and the spring needs to be tightened a full revolution for every foot of door height (e.g. 7-1/2 foot door = 7 revolutions +2 (30 quarter turns).
How many turns on a 8ft garage door spring?
A) The amount of turns required on your springs depends on the height of your garage door. If your door is 7ft high then we recommend starting off at 31 Quarter turns on each springs. If you have an 8ft door then start at 34 Quarter turns.
How many cycles should a garage door spring be?
The average garage door spring, if correctly installed, should last about 10,000 cycles of opening and closing. If you only go in and out of your garage once a day, that means you should expect a broken garage door spring around 14 years after the spring is first installed.
How do you wind a garage door torsion spring?
How to Wind Garage Door Torsion Springs Insert one winding rod snugly into winding cone, to full socket depth. Maintaining a tight grip on the winding rod rotate it slowly in the proper direction, as shown below.
How many turns on a 9ft garage door spring?
A rule of thumb with springs is that four quarter turns equals a full revolution and the spring needs to be tightened a full revolution for every foot of door height (e.g. 7-1/2 foot door = 7 revolutions +2 (30 quarter turns).
How do I know what size torsion spring I need for my garage door?
Basically, you run a tape measure along the length of a spring, and take down the number of inches. Therefore, if your tape measure indicates that a torsion spring is 36 inches from one end to the other, that’s a 36-inch — or three foot — torsion spring.
How much tension should be on a garage door spring?
You would want to tighten the adjuster a full turn clockwise to add tension if the door closed easily without holding up halfway. However, you will want to loosen the adjuster three turns counterclockwise if it was too tight.
Which way do you wind a garage door spring?
Basically, door springs can either wind to the left or to the right. Right-hand winding springs wind in a clockwise manner with the end wire on the right, while left-hand winding springs go anticlockwise with their end wire on the left.
Can garage door springs be too strong?
When garage door springs are too large, they provide more strength than the door needs. It will open with too much force, rolling up very quickly and compromising its safety. Kids or even unprepared adults could be knocked over by the sudden force when they try to open it.
How long should a torsion spring last?
The average home opens and closes a garage door four times daily, and, with a 10,000-cycle torsion spring, this translates to a lifespan of approximately seven years. Thus, high-cycle springs can have lifespans that last from 14 to 20 years.
How do you calculate torsion spring force?
Torsion spring torque is calculated the same way you calculate a working load. To calculate the torque of a torsional spring you must divide the spring rate by the amount of degrees of deflection your spring will be required to travel.
What weight garage door springs do I need?
This is determined by the pitch with which the springs are wound. On sectional garage door springs, this normally is 15 percent. For example, a 100-pound pull spring requires 15 pounds of weight to separate the coils; when a door is open, the two springs will support 15 pounds of door weight without any stretch.
Can you manually open a garage door with a broken torsion spring?
As professionals in the industry, we advise you do not attempt to open your garage door if the spring is broken. Extension springs on either side of the door, along the rails, help counterbalance the weight of the door as it is raised or lowered. Torsion springs across the top of the door help do the heavy lifting.
Can I use a longer torsion spring?
If your garage door springs have lasted less than five years, or if you plan to live where you are for many years, you may want to try the extra long life torsion springs. By using larger springs, you can, in most cases, quadruple your spring life while only doubling the cost of the springs.
How do I know if my garage door springs need to be adjusted?
More Noise Than Usual. A balanced garage door should be relatively quiet when traveling up or down the door tracks. If your garage door is making excessive creaking, grinding, or squeaking noises when opening or closing, your springs may be strained and most likely need to be replaced.
How many springs does a garage door have?
As a rule of thumb, a single garage door takes one torsion spring. A double-wide garage door takes two springs. However, if you have an exceptionally heavy single door, you may need two torsion springs. It is easy to tell whether you have one or two springs.
What is the color code on garage door springs?
Garage Door Extension Spring DASMA Color Code Chart Color Pounds Kilograms Brown 60/160/260 xxx Orange 70/170/270 30/75/120 Gold 80/180/280 35/80/125 Light Blue 90/190/290 40/85/130.
How much is a torsion spring for garage door?
Torsion spring replacement costs anywhere from $75 to $150 per spring, including both materials and labor. The springs alone run $30 to $100 each. You’ll almost always have two springs per door, and you should replace both at the same time.
