Table of Contents
The new perimeter-weighted F.I.T. (Focused Inertia Technology) Cam System on the 2017 Hype DTX includes a seamless draw cycle that makes this bow enjoyable to shoot. This bow has an 80% let-off and a smooth draw cycle.
How do you change the draw weight on mission menace?
Draw weight adjustments can be made by turning the limb bolt counter-clockwise using a 7/32″ Allen wrench (except for Menace®, which requires a 3/16″ Allen wrench). It is important to adjust both limb bolts in equal amounts. Do not exceed the recommended turns out from the maximum draw weight.
Where is the serial number on a mission bow?
The serial number on all Mission vertical bows can be found on the back shelf of the bow above the grip. It is engraved into the riser of the bow.
How do I measure my draw length?
To measure your draw length, stand with your back to a wall stretching your arms out against the wall. Measure the distance from the end of your middle finger to the end of your other middle finger, basically the length of both arms, hands and chest. This measurement, minus 15 then divided by 2, is your draw length.
How do you change the draw weight on mission Mxr?
Draw weight adjustments can be made by turning the limb bolt counter-clockwise using a 7/32″ Allen wrench (except for Menace®, which requires a 3/16″ Allen wrench). It is important to adjust both limb bolts in equal amounts. Do not exceed the recommended turns out from the maximum draw weight.
Does Mathews make mission bows?
We take great pride in the quality and craftsmanship of our Mission line. From start to finish, your bow is engineered and built by the same team that delivers our high-end Mathews bows, in the same quality controlled confines of our factory in Sparta, Wisconsin.
How do you change the draw length on mission venture?
The Voyager single cam powering the Venture is extremely adjustable, but draw length is cam specific; meaning shooters are only able to change the draw length by purchasing new cams and taking it to a shop.
How do you tell what year my Mathews bow is?
Read the serial number plate found at the edge of the grip. Write down the serial number and the date stamp. The date stamp will tell you the age of the bow. Check out the underside of the bow shaft toward the top pulley on some models to find the serial number and date stamp.
How do you find out what Mathews bow I have?
Locate your bow serial number in the riser cutout where your cable rod connects to the riser.
Do all crossbows have serial numbers?
The crossbow serial number can be located in one of two places. It will be a seven digit number starting with a 9. If not, then turn your crossbow upside down and look inside the rail, towards the stock, behind the trigger assembly. The serial number will be on a sticker and start with XB followed by five numbers.
When did the Halon 6 come out?
Mathews Halon 6 Description A compact hunting bow at 30 inch axle to axle and generating up to 345fps IBO, the Halon 6 is designed to be highly manoeuvrable. The Halon takes the popular No Cam technology released in 2015 and creates a much faster harder hitting compact package.
How long should arrows be for 29 Draw?
How to: Select the perfect arrow Bow Arrow length Draw weight lb. 25″ 29″ 15-20 700 600 20-25 700 600 25-30 700 500.
How long should my arrows be for a 28 draw?
If you’re a 28-inch draw length and want an arrow that ends at the front of the riser, your arrow length would be around 27 inches. However, your arrow length can be longer if you need to weaken the spine of your arrow. For safety reasons, your arrows shouldn’t be cut too short.
How long should arrows be for a 30 inch draw?
The Easton spine chart recommends a spine of 250 for a 30-inch arrow shot from a bow set at 70 pounds. Cut that arrow length down to 28 inches, and the spine chart recommends a 340 spine.
How do you adjust the draw weight on a compound bow?
To adjust the draw weight, we have to unload or load more stress (flex) on the limbs; we do that by tightening or loosening the limb bolts. To raise draw weight to maximum poundage, tighten the limb bolts (clockwise) until both limbs are tight against the riser.
Is the mission Mxr a good bow?
Overall rating: 5 out of 5 based on 1. The MXR is a one-of-a-kind, high-performance hunting bow offering accuracy and speeds traditionally found in higher priced bows. Built around our Crosscentric Cam technology, the MXR is powerful and efficient. This performance-inspired bow is unlike any in its category.
Who owns prime archery?
Why is G5 and Prime Bows soaring to the top of the archery equipment and compound bow market? For that question we provided an inside look at the company and the owners Lou, Nate, and Matt Grace.
Where are Hoyt bows made?
Louis, Missouri, to today’s world-class, 150,000 square foot manufacturing facility in Salt Lake City, Utah, Hoyt has been the world’s premier bowmaker. Just as in the past, today every Hoyt bow features a long list of technologies and innovations.
How much is the Mathews V3?
Today, November 17, is the launch date for their 2021 line of hunting bows! For 2021, their flagship bow is the Mathews V3 that comes in a couple of options: a 31” ATA and a 27” ATA. Mathews 2021 V3 Bow Specs MSRP $1,199 $1,199.
Does Mathews crossbow?
Mission Archery, the hugely popular off-shoot of Mathews Inc., has entered the crossbow market. The crossbow’s riser doubles as a foothold and eliminates the extra bulk of a stirrup. The Mission crossbow’s cam system produces amazing speeds up to 360 fps.
What year did Mathews Switchback come out?
Mathews introduced the first Switchback in 2005. Based on reports from the field it has been an extremely successful bow, heralded as the best-selling Mathews bow of all time.
What was the first Mathews bow?
Mathews MQ1: The SoloCam Classic The first Mathews was called the Standard, and the second was the UltraLight—a bow that McPherson still regards as a personal favorite. Company sales increased by 400 percent that year.
When did Mathews SoloCam come out?
In 1992, I invented Solocam technology and started Mathews Archery. From the very first bow design to the latest flagship model, our intention is, and has always been, to maintain every aspect of the build in-house.
What year is the Mathews Z7 Extreme?
Mathews Inc. has been on the top single cam market for several years and they plan on maintaining that lead with the introduction of the Z7 for 2010.
