Table of Contents
QUIKRETE® Concrete Bonding Adhesive (No. 9902) permanently bonds new concrete, plaster, and stucco to existing concrete, plaster, and stucco. Eliminates the need for roughing the surface before the application.
How do you attach concrete to old concrete?
Drill 5/8-inch diameter holes six inches deep into the old concrete. Flush the holes with water. Inject epoxy into the backs of the holes. Insert 12-inch lengths of rebar into the holes, twisting them to ensure an even coating of epoxy around their circumferences and along their lengths within the holes.
Does concrete adhere to old concrete?
The cement within a concrete mix doesn’t contain any natural bonding agents – so when fresh concrete is added on top of an existing layer of concrete, the two won’t join together. The new won’t adhere to the old without the help of a bonding adhesive.
What is the best adhesive for concrete to concrete?
When it comes to reliability, we consider Loctite as the best adhesive for concrete blocks. Loctite adhesive offers enhanced adhesion to nearly all construction materials. It’s suitable for both indoor and outdoor projects plus is nearly three times stronger than ordinary construction adhesives.
Can I pour concrete over dirt?
Long story short, yes you can pour concrete over dirt.
Can I pour a 2 inch concrete slab?
If done properly, new concrete can often be poured right over an existing slab. For this to be feasible, the contractor needs to pour at least 2 inches thick, use smaller aggregate, and incorporate reinforcement such as welded wire mesh or fiber mixed into the concrete.
What is poor man’s concrete?
We have a few companies locally that offer “poor man’s concrete”. I’m not sure exactly what it is, but I’ve seen it in driveways and such. It’s a white powdery material they dump and flatten out and when it gets wet, it’s supposed to harden like cement.
How do you attach something to concrete without drilling?
If you are willing to make holes in the concrete but do not want to buy the particular drill bit needed, then the simplest solution is to get nails for your project. Standard nails will not work on concrete, but some nails are made specifically for nailing wood to concrete. Cut nails will also work for this as well.
Can I use liquid nails on concrete?
LIQUID NAILS® Concrete & Mortar Repair, (CR-805), is a weather-resistant indoor/outdoor acrylic compound with silicone, ideal for repairing and sealing cracks and joints in concrete and masonry surfaces. This easy-gunning sealant dries gray similar to concrete or can be painted.
Is there an adhesive for concrete?
Concrete glue is an adhesive designed for adhering porous concrete to other surfaces—a difficult task without the right product. In fact, you can use a construction adhesive for gluing metal to concrete, fixing up crumbling roadways, and even garden stones. Whatever the job, there’s an adhesive to help you get it done.
Do you need gravel under concrete?
Whether you pour concrete for a walkway or patio, a strong gravel base is required to prevent the concrete from cracking and shifting. Gravel is especially important in clay soil because it doesn’t drain well, which results in water pooling under the concrete slab and slowly eroding the soil as it finally drains.
How do you prepare ground for concrete?
Preparation is the most important aspect of pouring a concrete slab. Dig the ground down to the proper depth. Smooth out the ground with the flat side of a rake so that you have a level surface. Tamp the ground with a hand tamper or mechanical tamper. Pour 2 inches of small, rounded gravel for additional drainage needs.
What kind of gravel goes under concrete?
Most concrete contractors want a mix of coarse and fine aggregate to create a compactable base that is going to be safe for settlement and drainage. Crusher run (a mix of crushed stone and stone dust) is one of the best base materials for concrete flatwork.
How strong is 6 inches of concrete?
For example, a 6-inch pad with a compression strength of 700 psi can support 1,105 psi. If it was 7 inches thick, it could support 1,194 psi, and if it was 12-inches thick, it could support 1,563 psi.
Is 2 inches of concrete enough?
A: Concrete is typically applied at a thickness of 2 inches or more, but the thicker it is, the stronger the slab will be. Four inches is most common for a slab. Products labeled “High Strength Concrete Mix” are ideal for these types of applications.
Can I pour a 3 inch concrete slab?
Here, pouring a concrete slab 4 inches in thickness is fine. While you may choose to reinforce it with rebar, wire mesh should be sufficient. A 3- to 4-inch slab will work for the floor of a storage or tool shed, workshop, garden shed, or playhouse.
What is a good substitute for concrete?
Concrete: Cement Substitutes Pulverised Fuel Ash (PFA), aka ‘Fly ash’ as a cement substitute. PFA is a by-product of coal-burning power stations. Ground Granulated Blast-furnace Slag (GGBS) as a cement substitute. GGBS is a by-product of the iron and steel industry. Silica fume. Limestone fines. Alternative fuels.
What are the alternatives to concrete?
We have collated 11 green building materials that offer alternatives to concrete, and a lower environmental impact. Straw Bales. Grasscrete. Rammed Earth. HempCrete. Bamboo. Recycled Plastic. Wood. Mycelium.
How long do you leave forms on concrete?
The forms or “molding” that holds the concrete in place until it dries should be left alone for at least two days to ensure that the concrete is completely dry. If the forms are removed too soon, the concrete can begin to sag, crack and collapse, especially if conditions like temperature affected its strength.
How do you secure something to concrete?
Simply drill a hole into the concrete, hold the fixture you’re fastening over the hole, then use a hammer to tap the anchor into the hole. As you drive in the pin, the sleeve expands outward, trapping the anchor in the hole.
Does Gorilla Glue work on concrete?
Gorilla 2 Part Epoxy is useful for gap-filling, repairing exterior siding, or gluing plastic, wood, metal, ceramics, brick, stone, concrete, glass, and foam. The epoxy is water-resistant (though not waterproof) so it can hold up fairly well when used on outdoor items.
