Table of Contents
Standard Drawers (about 12″ – 36″) Standard-sized drawers can use any of the following pull sizes: 3” (one or two), 4” (one or two), 96mm, and 128mm.
How are dresser drawer handles measured?
To measure drawer pulls, you must determine three measurements: length, center-to-center distance, and projection/depth. With knobs, focus on projection/depth measurements, since most knobs will not be particularly tall or wide.
How do you measure for a new drawer handle?
Place the drawer pull on a work surface with the threaded posts facing up. Measure from the center of the screw hole in one threaded post over to the center of the other screw hole with a tape measure. This is the measurement required when selecting replacement pulls.
Can you change the size of drawer pulls?
One of the most common problems with changing the hardware on older pieces is when drawer holes don’t fit standard pulls. While it takes a little effort, you can easily move or resize hardware holes and still pull of a professional finish.
What size drawer pulls for 36 inch drawer?
Pulls 3-7 inches in length will sit the most comfortably on doors less than 24 inches tall. Cabinet doors 24-36 inches tall are best adorned with pulls 7-12 inches long, while cabinets taller than 36 inches such as pantries, built-in appliances and pullouts should be accompanied by pulls longer than 12 inches.
Are all drawer pulls the same size?
There is no right or wrong size to choose, but we do recommend choosing pulls that have at least a 3-3/4″ center to center (the distance between the screw holes). If you choose to use a smaller size throughout, we highly recommend using two pulls on wide drawers.
How do I measure for replacement cabinet handles?
Measure the distance between the two screws from the centre of each screw. This will give you your ‘fixing centres’ and is the measurement you need when buying your new handles. Our handles are all listed with a measurement appended to the title. This measurement is the ‘fixing centre’, NOT the total length.
How do you measure drawer slides?
Measure the box, not the drawer front Start at the back of the box and measure to the front of the box without including the face of the drawer. Once you have the length, round the number down. For example, if the drawer is 20 ½ inches long you will need to purchase 20 inch drawer slides.
How do you find the center of a drawer?
Move the ruler across the drawer front diagonally in the other direction, from top right corner to bottom left corner. Trace the inner line of the ruler. Where the two lines intersect is the center point of the drawer, centered horizontally and vertically.
What are standard drawer pull sizes?
For standard size cabinetry (dimensions of 12″ – 36″) the most common pull sizes are 3”, 4”, 96mm, and 128mm center to center (from one screw hole to another).
Can you mix cabinet pull sizes?
There’s no “rule”, it’s a matter of looking at as many kitchens as possible and figuring out the look you prefer. I also used a variety of sized pulls on drawers of different widths, and used Restoration Hardware.
Do you put pulls on fake drawers?
I would recommend putting pulls on the dummy drawers it allows for consistency. Good design is always consistent. It will also give the illusion that these drawers are not fake. The idea of putting a minimal intrusive towel bar works well because then it will serve more for function then aesthetics.
What size cabinet pulls for 30 inch cabinet?
Small Drawers that are 12” or less typically work best with a pull that is 3” to 4” long or a knob that is 1” in diameter. Large Drawers that are 30” to 48″will require a pull that is longer than 8″ or a knob that is 1″ in diameter or greater. Using two pulls or knobs for a large drawer also works great.
What size drawer needs two pulls?
Drawers wider than 18″ need two knobs/pulls, whereas drawer narrower need only one. If a drawer is wide enough to need two knobs, they should be set about 1/6th of the drawer length from each end (roughly).
What size are drawer pull screws?
Standard #8-32 machine screw, used for drawer front knobs and pulls. Different length screws used for installing pulls and knobs.
What size should cabinet knobs be?
Knobs that are 1 ¼” to 1 ⅜” are standard for most applications. Any knob that is 1 ½ inches or larger is generally used on larger cabinets or if someone is really trying to make their hardware stand out and look more dramatic.
What is center to center measurement for cabinet pulls?
The Center-to-Center of any drawer pull is the distance between the center of one screw hole to the center of the other. Measuring the center-to-center of the drawer pull is key in determining what new hardware will fit and whether you’ll need to drill new mounting holes or fit into existing ones.
How do you change a drawer knob to pulls?
Fill the original hole (and any uneven surrounding areas) with wood putty. After the wood putty has dried completely, sand smooth with medium to fine grit sandpaper, removing all excess filler. Paint or stain the filled area, then drill holes to fit the new screws for your pulls in the area previously marked.
How do you put hardware on a dresser?
How To Replace Old Furniture Hardware With New Drawer Pulls Prepare the furniture for painting. Remove the original hardware. Drill a hole for the new hardware. Protect the inside of the drawer. Fill old hardware screw holes with wood filler. Sand the wood filler. Paint the furniture.
Are cabinet pulls standard size?
What is the industry standard size for cabinet pulls? For cabinet pulls, standard center-to-center screw holes measure from 3 to 5 inches apart, or 64, 96, and 128 millimeters apart.
Are kitchen handles standard size?
Standard pull handles tend to range between 3 and 4 inches (96 to 128mm) in width, with smaller T-pulls often used for small cabinets and drawers. As a rule of thumb, the larger the drawer or cabinet, the larger the handle should be.
