Table of Contents
Where should drawer knobs be placed?
On wall cabinets, knobs are usually placed 2-1/2” to 3” from the bottom corner of the door. On base cabinets, they are placed 2-1/2” to 3” from the upper corner of the door. If your drawer is 24” or wider, you may choose to place a second knob.
Should drawer knobs be centered?
As far as the height of your drawer hardware, the classic choice is to center them vertically. With multiple drawers stacked on top of each other, choosing this placement makes each knob a little lower and harder to reach.
Should drawer pulls be longer than cabinet pulls?
Pulls come in a variety of styles and lengths, which can prove to be daunting when selecting proportionately sized hardware. Bar Pulls are traditionally measured center-to-center and they should not exceed 1/3 of the length of a cabinet door or width of a drawer.
Where should knobs go on cabinets?
Cabinet knobs should be installed on the stile opposite the hinges. The general rule is to place a knob 2 1/2″ – 3″ from the corner of the door. For upper cabinets, install knobs in the bottom corners of the door. For lower cabinets, place them in the upper corners.
Where do you put knobs on kitchen cabinets?
For both upper and lower cabinets, the pulls should be installed vertically 2 ½ – 3 inches in from the corner of the door. For drawers, they should be installed horizontally in the center of the door. While there is no hard-set rule for the size of your pulls, consider using longer ones on larger drawers and cabinets.
How long should drawer pulls be?
Determine Size While there is no set rule, we generally recommend that the pull length is approximately 1/3 of the cabinet or drawer width. Small Drawers that are 12” or less typically work best with a pull that is 3” to 4” long or a knob that is 1” in diameter.
Should kitchen handles be vertical or horizontal?
The universal rule is that handles are placed vertically on doors and horizontally on pull-out drawers. Stand in your new kitchen and hold your handles against the drawers and cabinet doors to try out different heights and positions for each of them.
What is the rule of thumb for cabinet hardware?
An oversized cabinet door or drawer needs a large piece of hardware for proper functionality. A good rule of thumb for traditional or transitional style pulls is that they should be about one-third of the length of the cabinet drawer. Drawers larger than eighteen inches wide may require more than one pull or knob.
What does center to center mean on drawer pulls?
The Center-to-Center of any drawer pull is the distance between the center of one screw hole to the center of the other. Measuring the center-to-center of the drawer pull is key in determining what new hardware will fit and whether you’ll need to drill new mounting holes or fit into existing ones.
Should I use knobs or pulls on kitchen cabinets?
There are no strict rules to follow when choosing whether to select a knob or a pull or both. One preference is to use knobs for all doors and pulls for all drawers. For any large door such as a pantry and any pull-out door (including pull-out base pantries or trash pull-outs), use a pull.
Can you put knobs on drawers?
Yes, you can put knobs onto your kitchen drawers! The installation process is very easy, and many individuals even prefer it over installing traditional pull handles. The trickiest part might be deciding where to place the knobs on the drawers and placing them in the same spot on every drawer.
Where do knobs and pulls go on Shaker cabinets?
Center of the Stile: Knobs and pulls can be placed halfway up the stile of your Shaker door. Keep in mind you’ll want to be able to reach the handles, since they will be placed higher up along the stile. Just Above or Below the Corners: Place the knobs or pulls 2” to 3” from the lower or upper corner.
How long should drawer slides be?
Start at the back of the box and measure to the front of the box without including the face of the drawer. Once you have the length, round the number down. For example, if the drawer is 20 ½ inches long you will need to purchase 20 inch drawer slides.
What is an appliance pull?
Appliance pulls are long kitchen cabinet handles generally used in two places in the kitchen. The first is on wood panel covered appliances, usually refrigerators or dishwashers. The other popular use for appliance pulls is for tall pantry doors or oversized storage drawers.
What are standard drawer pull sizes?
For standard size cabinetry (dimensions of 12″ – 36″) the most common pull sizes are 3”, 4”, 96mm, and 128mm center to center (from one screw hole to another).
How do you measure for drawer pulls?
Place the drawer pull on a work surface with the threaded posts facing up. Measure from the center of the screw hole in one threaded post over to the center of the other screw hole with a tape measure. This is the measurement required when selecting replacement pulls.
Can you mix cabinet hardware finishes?
Mixing metal finishes can add dimension and visual interest to a room. Instead of a monochromatic, one-note space, you create intrigue and the illusion of texture. When you mix metals, you can blend styles, making a room look more or less modern depending on your personal taste.
