Table of Contents
Because your chainsaw will idle, but dies when it is revved up to full power, it means that the filter is only partially clogged; it will allow enough fuel to the engine to run on idle, but not enough to sustain full throttle. If the filter becomes clogged, not enough fuel will reach the engine for it to run properly.
Why does my chainsaw start and then die?
If the fuel filter is damaged, this debris can enter the lines causing a clog, and preventing your chainsaw from running. The fuel filter can also become clogged, and this will prevent fuel from reaching the engine, causing it to die. A fouled spark plug can cause your chainsaw to start but immediately die.
Why does my chainsaw only runs on choke?
If your chainsaw only runs with the choke on, it is likely an issue with your carburetor. If the carburetor is plugged, the engine will be starved of fuel and will not run. However, if the engine is plugged, the choke will pull more fuel through the carburetor’s idle circuit and allow it to run.
Why does my Stihl chainsaw dies when I give it gas?
An engine stalls when it’s getting too much or not enough fuel from the carburetor. Stihl chainsaw carburetors usually have three adjustment screws: one each for idle, low speed and high speed. If the saw stalls while it’s idling, adjusting the idle screw, which usually is marked LA, should help.
What causes vapor lock in a chainsaw?
Vapor lock occurs when the fuel (usually gasoline) within the fuel delivery system overheats and vaporizes too rapidly. Consider allowing the chainsaw to cool down for 10 to 15 minutes until vapor pressure has subsided and saw will start without removing gas cap.
How do you clean the carburetor on a chainsaw?
You can clean your chainsaw’s carburetor using the following five easy steps: ● Step 1: Clean the Air Filter. Step 2: Clean the Carburetor’s Intake Components. Step 3: Clean/Wash the Carburetor’s Needle Valves. Step 4: Work the Pull Cord. Step 5: Drain the Old Fuel and Add Fresh Fuel. Step 1: Blend the Cleaner With Gas.
What does a spark arrestor do on a chainsaw?
The spark arrestor on your chainsaw prevents dangerous hot sparks from igniting fires while you’re working. If the arrestor is clogged or dirty, however, it will also prevent exhaust from leaving the motor, which can prevent it from running.
Why does my small engine only run on full choke?
An engine that requires the choking ( partial or full ) after initial engine warm up is an indication that the engine fuel air mixture system is out of adjustment. Both the manual choke system and the manual primer system engines may experience this similar symptom of running only when the fuel mixture is enriched.
Why does engine only run with choke on?
If a motorcycle or ATV only runs with the choke on, it’s because the richer “choke on” mixture is actually closer to the engine’s normal operating fuel mixture than the leaner “choke off” mixture. So when the choke is turned off, the engine gets too little fuel and too much air for it to run and it stalls.
How do you adjust the high and low on a Poulan chainsaw?
High and Low Speed Adjustments Start the chain saw as you normally do and let it idle, making sure the chain does not touch anything. Insert a small flat-head screwdriver into the idle speed screw and turn it clockwise to increase the engine speed if it idles too slowly.
How do you adjust a Stihl carburetor?
Turn the H screw clockwise with a carburetor adjustment tool until the head is spinning as fast as it will go, then back off the screw carefully until the RPMs start to decrease. Turn the screw slowly clockwise again until the engine once again just starts to pick up speed.
What are signs that your fuel pump is going out?
If you notice these six signs, consider taking your car to your local dealership to have the fuel pump replaced. Whining Noise From the Fuel Tank. The Engine Sputters or Surges. Trouble Starting the Car. Loss of Power Under Load. Reduced Gas Mileage. Stalling at High Temperatures.
What are the signs of a bad fuel injector?
Below are the most common symptoms of bad fuel injectors. Check Engine Light Illuminates Solid or Flashes. One of the engine issues that can cause the check engine light to come on or flash is a dirty or malfunctioning fuel injector. Rough Idling/Irritating Idle Noise. Engine Misfiring. Fuel Leaks.
What are the symptoms of low fuel pressure?
Low Fuel Pressure Symptoms Unresponsive Throttle. All cars require proper fuel delivery to their cylinders for them to run properly. Difficulty Starting the Car. Low fuel pressure will also make it hard for you to ignite your car’s engine. Stalling Engine. Check Engine Light Comes to Life. Turbo Lag. Misfires. Low Performance.
What are signs of vapor lock?
Vapor lock causes: Loss of fuel pressure (and flow) Loss of power. Stalling. Difficulty restarting the engine.
Do you start a chainsaw with the brake on?
When engaged, the chain brake stops the chain from rotating around the saw’s guide bar. When using a chainsaw, you should always start it with the chain brake engaged so the chain does not move.
Why does my chainsaw cut out when hot?
When your chainsaw quits after it gets hot, you either have a problem with gas flow being restricted into the engine or with the spark. This is a common occurrence on older-model chainsaws. By replacing your spark plugs and keeping your gas lines clear you can reduce the chances of this problem recurring.
