Table of Contents
Draw weight adjustments are made using either a 3/16” or 7/32” Allen Wrench. Turn the limb bolt clockwise to increase the draw weight and counter clockwise to decrease the weight. Both limb bolts must be adjusted equally, or the bow may become out of tune/synchronization. The limb bolt should be snug.
Can you adjust Mathews draw length?
With the exception of the Mathews Mission series, Mathews bows are designed draw length specific, and do not provide for setting adjustment. While the Mission series draw length can be changed with a setscrew on the cams, you will need to replace the cams to change the draw length on other models of Mathews bows.
How do you adjust the draw length on a Mathews bow?
The draw length on your bow is adjustable on the cam a maximum of one inch down from the peak draw length. This is accomplished by moving the string loop to any of three adjustment posts on either side of the cam.
Does Mathews draw length run long?
Absolutely! If you’ve been in this sport for any length of time you will know that they typically run 1/2 long.
How do you change the draw length on a Mathews no Cam?
Simply remove the two allen screws that hold the module to the wheel and install your new module in it’s place. As noted earlier these modules can change both your draw length as well as your let-off, which will change your bow’s speed. The lower the let-off the faster the bow.
How do you change the draw length on a Mathews z3?
The cams are designed to be draw length specific, which means they cannot be changed with rotating or replacement modules.
Do I need a bow press to adjust draw length?
Draw length specific cam bows use specific cams to deliver different draw lengths. The changing out of a compound bow’s cam is complicated and requires the bow to be pressed. If not qualified to do such work, the archer should have this procedure done at their local pro shop.
How do I measure my Mathews draw length?
While standing naturally, have a friend grab a measuring tape and measure across your back from the tip of one finger to the tip of the other. Divide that number by 2.5 to find the draw length that is right for you.
How much does the Mathews prima cost?
The all-new 2021 Mathews Prima is a great new bow. It’s lightweight, compact, and comes with all the same bells and whistles as the V3. With an MSRP of just $1,099 it provides tremendous performance in a small package.
How do you change the camera on a Mathews z7?
It’s really simple. Press the bow. Remove string and Buss Cable. Remove bow from press. Slide the plastic retainer from axle. Remove axle. Cam is free.
How do you change the draw length on mission venture?
The Voyager single cam powering the Venture is extremely adjustable, but draw length is cam specific; meaning shooters are only able to change the draw length by purchasing new cams and taking it to a shop.
Does Mathews vxr have adjustable draw length?
Proven accurate in the field, this revolutionary cam system, allows you to change draw length and peak draw weight into 5 pound increments with the simple change of a mod. available in 60,65, 70 and 75 pound peak weights, each set of mods are programmed for an incredibly smooth draw and maximum efficiency.
How long should my draw length be?
Resist the temptation to make your draw length longer than it should be, as this will effect your accuracy. Your wingspan typically is the same as your height in inches; So your height in inches minus 15 and then divided by 2 will be your draw length, or at least a very good starting point.
What should my draw weight be?
Build, Bodyweight and Suggested Bow Draw Weights Type of Person/Build Weight (lbs) Compound Suggested Draw Weight (lbs) Large/Strong Child 100-130 25-35 Small/Slight Woman 100-130 25-35 Average Woman 130-160 30-40 Large/Strong Woman 160+ 45-55.
What if my draw length is too short?
If the draw length is too short, you will feel “bunched up” or uncomfortable because you are too compressed. In addition, the elbow will have a fairly big bend in it in order for you to get the string to your face.
What if my draw length is too long?
Many bowhunters shoot a draw length that is too long for them, which hurts shooting form and degrades accuracy. You hear this all the time–that a long draw overextends your bow arm and makes it harder to hold against the back wall and to maintain a consistent anchor point.
Does draw length change with a release?
Registered. Your draw length will not change by using a longer release aid. The only thing changing is your anchor point.
How do I know if my bow draw length is too long?
The ideal draw length for you is the one that allows you to anchor in a comfortable position, with your bow arm elbow unlocked (slightly bent) and your release arm elbow and forearm pointing straight away from the target. If the release arm elbow points left or right, your draw length is too long or too short.
How much does it cost to adjust draw length on a bow?
Changing the draw length totally depends on what bow it is. If it has rotating mods it should be cheap. If it’s a mod swap it depends on the brand Hoyt is about $25 bucks and Elite is about $50 bucks. If it’s cam specific then it’s not going to be cheap your probably lookin at 100-150 bucks.
Does changing draw length affect sights?
Shortening the draw length will cause the peep to be higher, which will cause you to tilt your Bow upward to align peep with sight housing. This will make you hit higher. The Bow will be a little slower but you still may have to move the peep down or sight up.
How long should my arrows be for a 26 inch draw?
How to: Select the perfect arrow Bow Arrow length Draw weight lb. 25″ 26″ 15-20 700 700 20-25 700 700 25-30 700 600.
How long should my arrows be for a 29 inch draw?
it depends on the arrows you choose, you need at least 1/4″ of arrow overhang on the rest. so you can probably shoot an arrow that’s about 28 1/4 for rests that are set up normally. and go all the way up to full length 36″ arrows for indoor. i would suggest 1″ of overhang on your rest.
