Table of Contents
You should always use the longest slide possible for your application, without exceeding the drawer depth into the cabinet. The Height of a Drawer Slide is usually only a limiting factor, in the sense that you can’t install a slide that is taller than your drawer or pull-out.
Do drawer slides need to be full length?
Measuring for slides Taking accurate measurements ensures you buy slides that work in your cabinet. Follow these tips to make sure everything goes smoothly: Slides come in lengths from 10″ to 28″. A too-short slide prevents the drawer from opening fully, and one that’s too long won’t fit in the cabinet.
How deep should drawer slides be?
Most drawers are built to support a 1/2″ of clearance on each side of the drawer. However, heavy duty drawer slides will often take from 0.7 to 0.75 inches and undermount slides a custom amount less than 1/2″.
How much gap does a drawer slide need?
Most side-mount slides require 1/2” to 17/32” of clearance on each side of a drawer. That means each drawer should be 1” to 1-1/16” smaller than the opening to fit properly. Under-mount slides attach to the bottoms of drawer boxes and can’t be seen when the drawers are open.
How deep do drawers need to be?
Drawer depth or height is not critical, but the most common difference between the drawer and the opening is 3/4 inch. For example, if the opening measures 4 inches vertically, the drawer should be built 3 1/4 inches. This allows 1/4 inch at the bottom where the slide is attached, and 1/2 inch at the top for clearance.
How do I measure drawer slides?
Measure from the back of the drawer-front to the end of the drawer box. Only measure the box, do not include the drawer front. Round the measurement off to the lower number on the tape. For example, when the measurement is 22 1/2 inches, you need to purchase 22-inch drawer slides.
What sizes do drawer slides come in?
Shop by Drawer Slide Size Below 8-10″ Drawer Slides. 1-8″, 2-9″ and 9 versions of 10″ drawer slides from Hettich, Fulterer, and Hawthorne & Reid. 12″ Drawer Slides. 14″ Drawer Slides. 16″ Drawer Slides. 18″ Drawer Slides. 20″ Drawer Slides. 22″ Drawer Slides. 24″ Drawer Slides.
How do you measure for cabinet drawers?
Measure the cabinet opening height (inside frame to frame) and subtract at least 1/2” from the opening height. If your cabinet opening measurement comes to 3 3/4″ then you need to round down to a 3 1/2″ drawer box. For depth, we recommend subtracting 1″ from the length of the side-mounted drawer glides.
What size cabinet pulls for drawers?
Using a pull that is approximately 1/3 the length of the drawer is a good rule of thumb. For modern cabinetry, you can use extra long pulls that span nearly the entire width of each cabinet.
How tall should drawers be?
Depth: Standard depths are 14-inches, 16-inches and 20-inches. Height: The height of the drawer refers to the height of the drawer face. The actual height of the box is usually less. Standard heights are 5-inches, 7.5-inches, 10-inches and 12-inches.
What is the thickness of drawer slides?
Light duty slides might be as thin as 1/2″, while heavy duty slides may be over 3/4″ thick. Face frame cabinet slides are easier to install using the specific, optional, face frame brackets. Length sizing is usually simplified by checking manufacturer’s charts, where the drawer size and cabinet depth are both stated.
How tall does a file drawer need to be?
The recommended minimum interior drawer box height is 9-1/4”. Recommended exterior minimum drawer box heights would be as follows depending on the bottom thickness and bottom inset. File slots are centered on the front and back.
How deep are standard dresser drawers?
A standard dresser has between six and nine drawers, is around waist tall (26″ – 44″), is 36″ – 60″ wide, and is 16″ – 20″ deep. However, these can vary and you should choose an option that works best in your bedroom. To find the right dresser dimensions for you, decide where you’d like your dresser to go.
Can drawer slides be mounted flat?
Some full-extension (100% travel) slides can be flat (horizontally) mounted, but there will be a reduction in their load bearing capacity. Typically this will reduce to 25% of the side mounted load rating.
Can you use side mount drawer slides as undermount?
Additionally, side mounts are built to carry a limited load, and if it is used as an undermount, there is a huge possibility that it might bend and malfunction. So for these professionals, the answer to the question “Can you use side mount drawer slides as undermount” will always be no.
What are the easiest drawer slides to install?
Mounting location: Side mounted drawer slides are the most popular and easiest to install. Center mount and undermount are also options.
What are the different types of drawer slides?
There are 6 types of Drawer slides: Ball Bearing Drawer Slides. Soft close Ball Bearing Drawer Slides. Under mount Drawer Slides. Side Mount Drawer Slides. Center Mount Drawer slides. Roller Slides.
Can drawer slides be longer than drawer?
You should always use the longest slide possible for your application, without exceeding the drawer depth into the cabinet. The Height of a Drawer Slide is usually only a limiting factor, in the sense that you can’t install a slide that is taller than your drawer or pull-out.
Should drawer slides be on the middle or bottom of the drawer?
The taller the side means you will want to mount the slide more in the middle. On shorter h drawers you can mount them middle or at the bottom and it will work fine. On shorter drawers that you make, if you make them with the bottom applied to the sides, by mounting them to the bottom you can hide the plywood edge.
