Table of Contents
Cement particle boards or render boards are normally fitted on timber frame builds and then the rendering is normally carried out over the board. A lightweight render system is best suitable simply because it bonds better to the cement particle board and secondly it is more flexible.
Can you render onto Hardibacker?
Hardiebacker cement floor board is backboard used as an ideal substrate for vinyl, natural stone and ceramic tiles. Knauf Aquapanel Irior Cement Board is an ideal substrate for directly applied render finishes and can be used for exterior walls in ventilated systems,exterior ceilings.
Can you render over cement board?
Cement boards can be finished in numerous ways however, one of the most effective ways is to apply render. Not only does render enhance the external appearance of a property, but it improves its thermal performance and thereby reduces energy costs.
Can you render onto insulation board?
1. As an external base for render. Because they are unaffected by variations in temperature, being submerged in water or frost, they can be used externally on walls to provide a layer of waterproof, insulating cladding which can be rendered upon.
Can you render over OSB board?
The simple answer is that applying render directly onto the OSB is not an ideal situation – it’s important to remember that at the end of the day, OSB is wood.
Can you render on to wood?
The short answer is “yes.” It is usually possible to cement render over timber. The render mix cannot be applied directly to the plywood, as wood is not an ideal substrate for cement render. It’s not waterproof, so it may warp and bend as it absorbs water from the render.
What board can I render onto?
Most render manufactures state that their product can be applied over cement particle boards however from experience although that is correct I would advise that the render is kept as thin as possible, probably a maximum of 10mm in thickness.
How thick is render on render board?
You will typically find that the render carrier boards on the market come in two thicknesses of 9mm and 12mm; however we recommend using 12mm render boards where available to ensure extra strength and stability (Blueclad, for example, only do a 10mm board).
Can you cement render onto plasterboard?
Sand & Cement will not stick to plasterboard – however if the plasterboard is properly prepared it will do. Mix some sand in with neat PVA to form a slurry mix and roller this onto the plasterboard. However it should be noted that plasterboard is designed to have the finish coat applied directly to it.
Does K Rend need a scratch coat?
K-Rend is a household brand name associated with the application of scratch or monocouche render to a property. This product has a scraped texture or finish and should strictly be applied directly to a masonry wall including brick, block or an existing rendered surface.
Can you render onto Celotex?
It has been designed to act as a direct render solution, enabling the render system to be directly applied onto the insulation with no requirement for separate batten systems or render boards. ‘The introduction of SW3000 proves that Celotex really does know insulation inside and out. ‘Feb 8, 2012.
How much is K rendering?
You can expect to pay £30-£70 per square metre for K Rend’s silicone render depending where you are in the country.
What material can you render over?
There are many instances where you may decide to render over your existing surface.Most common surfaces that can be rendered Bathroom tiles. Red brick. Clay brick. Blueboard. Painted besser block. New block. Split face block. Polystyrene.
Can you render over external paint?
They can be applied over existing paint – however, the walls will need to be carefully washed, and the old paint sanded down if it is flaky, or unable to bond to the walls correctly. Painting your home can be achieved for less than £1000 – a fraction of the cost of rendering an existing painted home.
Can you render timber frame?
Knauf Aquapanel Exterior is ideal for use on timber frame, timber battens and metal framed structures. It is mechanically fixed to the timber/steel framework and the system build up is then suitable to receive a render, paint or further exterior cladding finishes, such as slip bricks or tiles.
Can you render on to plywood?
Plywood is not particularly waterproof and will inevitably absorb water from the basecoat, which can cause the wood to warp and therefore hinder structural integrity. To avoid this, render carrier board is an ideal solution, but the downside is that it can’t be applied directly on top of the plywood.
Can you render over MDF?
MDF can be patched with top coat quite well with no problems. That is small indentations etc. Joins in mdf cannot be taped and finished with plaster they will eventually crack and or the tape will lift.
Can you render over Pebble Dash?
Rendering over pebbledash is easy when you use the EWI-065 One Coat Dash Cover (OCDC)! Ensure that the pebbledashed wall is stable and secure by knocking the existing substrate with a shovel or hammer. Loose pebbles should be removed, and any areas of crumbling pebbledash should be stripped back completely.
What way round does render board go?
The board should be fitted with the coarse face out to receive the render and a 3-4mm gap left between each board.
Is render board fireproof?
It is made from a mixture of inorganic materials, glass fibre, wood fibre and non-woven cloths, giving it a unique structure. It does not contain asbestos, formaldehyde or hazardous volatiles. Rendaboard highly durable and is Class 0 fire rated.
What is the best mix for rendering?
Most renders are typically made up of sand, water, cement, and lime. A standard ratio used in creating this mix is 6 parts sand, 1 part cement, and 1 part lime (6:1:1). There is no particular type of cement that should be used; any kind will do.
