Table of Contents
Do you polish any concrete? Yes! This means that any pre-existing concrete surface can be polished to your desired exposure and finish!.
Can you polish existing concrete?
Almost any structurally sound concrete floor, whether new or old, can be polished. Some retail and warehouses facilities that plan to polish their floors after placement may specify a floor that is as smooth as possible to minimise the polishing steps required.
How do you clean concrete after removing tile?
Use a scraper, metal scrubber or flat head screwdriver to remove as much of the cement as possible. For the remaining cement, apply the phosphoric acid following the manufacturer’s instructions. Once the cement loosens, scrub the area with a scrubber until it is all removed from the surface.
Can you stain concrete after tile removal?
In most cases, once you remove the existing flooring, you can stain the concrete subfloor as long as it’s in good condition. Remove existing carpeting, sheet vinyl, and tile as well as any adhesives or mastic used to glue down the flooring.
Can you polish concrete over tiles?
One of the most commonly asked questions Geostone receives is: ‘can a polished concrete floor be laid over an existing slab or floor tiles? ‘ We encourage all of our customers to discuss their individual circumstances with their concrete installer, but the short answer is, it can be done – sometimes.
How do I make my concrete floor shiny?
Regular sweeping and weekly cleaning with a mop and mild solution of dish soap and water should help concrete keep its shine. Every few months, use a pressure washer to clean dirt and debris from crevices. Make sure the concrete can handle the high-pressured stream of water before you tackle the entire project.
Can you put a thin layer of concrete over concrete?
How Thin Can You Pour Concrete Over Existing Concrete? The thinnest that is usually used when pouring concrete, in general, is about 2 to 2 ½ inches. That also applies to this pouring new concrete over old concrete. Any thinner than 2 inches would be too thin.
How hard is it to remove tile?
Removing floor tile can be a difficult and time-consuming project and the challenges often remain hidden until the project is underway. Depending on the construction, the tile may be attached to bare cement, a plywood or mason board underlayment or even affixed to a previously installed floor.
How much does it cost to remove tile from a concrete floor?
Tile Floor Removal Cost On average, you can expect to pay between $1.50 to $4.15 per square foot of ceramic tile for tile removal, according to Costimates.com. Let’s say your bathroom is 100 square feet. You can then expect to pay between $150 and $415 for the tile removal process.
How do you remove tile from concrete without breaking it?
Start by removing all the grout using a grout saw, rotary cutter, oscillating tool, or utility knife. Next, position a chisel in the grout line under the bottom of the tile, and tap it gently with a hammer to see if the tile will pop loose (be careful not to chip or crack the adjoining tile).
How do you prep a floor after removing tile?
Remove the Old Tile To remove old tile you’ll need to get a few things out of the way. Removing tile can get dusty. Use a hammer and chisel to break up a small area of the old tile. After you have removed the tile, use a floor scraper to remove any old thinset. Determine your subfloor type.
How do you break up tile on concrete floor?
There is no easy way to remove tile from a concrete floor. It is a matter of chiseling up the tile, either by hand or using an electric tool such as a small jackhammer or tile stripper. Also bear in mind that removing the tiles is generally the easy part of the removal process.
How do you repair concrete after removing tack strips?
Wipe across the damaged concrete with a wire brush to remove cracked or chipped edges from the tack-strip nail holes. Sweep the area with a broom or small brush to remove any loosened concrete, dirt or other debris. Mix a quantity of epoxy concrete patch according to the manufacturer’s directions.
How do you polish concrete tiles?
Follow these steps to polish your cement tiles: Use a fine (600 grit) sand screen disc to lightly sand the surface of the tiles. Seal with either a good quality penetrating sealer. Buff with a white pad.
Is it easy to polish concrete floors?
Polishing concrete is not an easy DIY project, since it requires heavy equipment and special diamond tooling. We recommend hiring a professional concrete polishing contractor to complete your project. They will have a thorough understanding of what it takes to achieve the best results.
Can you use quick shine on concrete floors?
Yes, Quick Shine will provide a high gloss shine on any hard surface floor.
What is the best way to clean concrete floors?
How to Clean Concrete Floors Clear debris. Clean and clear the floor of all debris, dirt and dust using a vacuum, soft bristle broom or dry dust mop. Apply Simple Green Multi-Surface Floor Care. Spray the cleaning solution as a light mist across your floor section by section. Mop up in sections. Dry.
What can I use to clean a concrete garage floor?
Mix a half-cup baking soda in a gallon of warm water and use it as an all-purpose cleaner. You can also mix baking soda with a few drops of liquid soap, to make a paste, and use it to scrub light stains. Don’t underestimate the power of warm, soapy water to keep your floors clean and remove minor stains.
What do you use to bond concrete to concrete?
QUIKRETE® Concrete Bonding Adhesive (No. 9902) permanently bonds new concrete, plaster, and stucco to existing concrete, plaster, and stucco. Eliminates the need for roughing the surface before the application.
Can I pour a 2 inch concrete slab?
If done properly, new concrete can often be poured right over an existing slab. For this to be feasible, the contractor needs to pour at least 2 inches thick, use smaller aggregate, and incorporate reinforcement such as welded wire mesh or fiber mixed into the concrete.
