Table of Contents
While tile can be laid on plywood, do not install tile directly onto the plywood subfloor itself. Use intervening layers of two sheets of plywood.
Do I need to prime plywood before tiling?
If tiling on fibre-reinforced cement sheets, or plywood/chipboard, then we would always recommend priming the reverse side and edges with BAL Bond SBR. This helps protect the plywood from moisture penetration which could cause the board to swell.
What do I put between plywood and tile?
On a plywood subfloor, you need either a layer of cement backer board or an underlayment membrane, like Custom Building Products’ Wonderboard and RedGard, between the subfloor and tile for the thin-set adhesive to achieve a good bond.
How level should a subfloor be for tile?
As noted in the first answer above, the surface to be tiled, in your case the floor, must be flat within 1/8” in 10′ when measured from the high points of the floor. To achieve this, be sure to use the appropriate patch or self-leveling compound (with the same manufacturer’s primer), but never thin set mortar.
How many layers of subfloor do I need for tile?
As to how many layers of subfloor, tile substrate should be a minimum of 1-1/8″, best provided with two layers of 5/8″ ACX plywood, never use osb or particle board under tile.
What thickness plywood should I use for bathroom flooring?
Plywood as a Subfloor Material Traditionally, exterior grade plywood has been the subfloor material of choice for many bathroom flooring projects. Plywood is made by gluing alternating layers of wood veneer. CDX plywood (¾”) in particular is used often because it has a high level of resistance to moisture and humidity.
Is cement board stronger than plywood?
Yes,the cement board is stronger than plywood. The cement board is normally used in external areas exposed to environmental exposures. The plywood is used internally.
Can you put Thinset on wood?
Does Thinset bond to wood? Whatever type of plywood you are dealing with, you need to use a rated thinset mortar that is designed to be used with wood. Most thinsets are designed to only work with a concrete or fiber board underlayment, not with wood.
What do you seal plywood with before tiling?
Plywood requires the application of a latex based bonding solution to the plywood to seal it and then the use of a flexible cement based adhesive, not pre-mixed tub adhesive.
What primer should I use on plywood?
Water-based primers will raise the grain of the wood, resulting in a rough surface. Use a non-water-based primer. Work in a well-ventilated area and wear a dust mask and eye protection while sanding. Wear eye protection while painting.
How thick should Plywood be under tile?
The subfloor under the tile should be at least 1 1/8″ thick, with a minimum of 5/8″ thick exterior grade plywood topped by 1/2″ cement backer board.
How do you install plywood over existing subfloor?
Instructions For Installing Another Layer Of Plywood
- Acclimate the underlayment. Store underlayment in the room it will be installed in for 72 hours before the actual installation.
- Clean the subfloor.
- Start installing the plywood.
- Staple the boards in place.
- Fill the seams.
What is stronger OSB or plywood?
Osb is stronger than plywood in shear. Shear values, through its thickness, are about 2 times greater than plywood. This is one of the reasons osb is used for webs of wooden I-joists. However, nail-holding ability controls performance in shear wall applications.
Does tile grout stick to wood?
The silica sand adds great durability to the grout. When you grout, you have to be very careful where the grout touches the up against the wood table. If you use sanded grout, the sand can scratch the wood finish. Don’t get any more grout on the wood than is necessary.
Do you have to put cement board under tile?
In short, tile and grout are not inherently waterproof. Cement backer board is often used as a tile base on plywood or OSB subfloor. Cement backer board on concrete as a subfloor or underlayment is usually not recommended or needed. In most cases, you can apply tile directly to the concrete.
Is my subfloor strong enough for tile?
Tile installed over wood floor systems MUST have a minimum of 1-1/4 inches of solid material beneath it. This means you can have a 3/4 inch wood subfloor covered by 1/2 inch plywood, cement board, or approved gypsum fiber underlayment.
Will Thinset stick to plywood?
Thinset sticks just fine to plywood, but that’s not really the question in your post. Thinset is the wet base that you first trowel on the plywood to make the tile stick. Higher latex content is essential for bonding to plywood. A quality unmodified thinset should be used and mixed with a latex additive.
Will tile mortar stick to wood?
Will tile mortar stick to wood? In any case, to bond tile to wood, you must use a flexible thin-set mortar with a latex additive. Wood shrinks and swells with humidity and frosts, which can break the bond between ordinary tile and thin-set.
Can you attach tile to wood?
Glue, called mastic, is the least expensive method for installing tiles. Mastic adheres the tile directly to a wooden sub-floor, to a wooden back-splash or onto a piece of plywood. Level the surface using a wood filler. Fill in all large gaps and holes as these will prevent proper adhesion of the tiles.
What kind of subfloor do I use for tile?
Tip: Make sure the subfloor will not deteriorate when it gets wet. Particleboard is not an acceptable subfloor material for tiling projects. Oriented strand board (OSB) and exterior-grade plywood will work if first covered with a latex-modified mortar and a tiling backer board.
What is the best backer board for a shower?
Cement board is a good, reliable backer board that works well on both floors and walls. Keep in mind that most tile setters err on the side of caution and brush a waterproofing membrane on top of cement board when it is in wet areas like showers or tub surrounds.
What kind of plywood do you use for subfloor under tile?
Exterior-Grade Plywood Exterior plywood is an acceptable underlayment for tile and is preferred to interior-grade plywoods because the bonding adhesives used are waterproof. If water seeps through the tile installation to the underlayment, it will not cause the wood to swell, as happens with interior-grade plywood.
