Table of Contents
Adjustable cams allow the archer to adjust his or her draw length with the use of an hexagonal wrench without, in most cases, pressing the compound bow. Adjustable compound bow cams allow archers to adjust anywhere from 3 inches up to 13 inches depending on the compound bow.
Can you change draw length without bow press?
All draw length adjustments can be made without the use of a bow press. Draw length changes are made by simply moving the draw stop to the desired position, then rotating the modules accordingly. See draw length settings below. To change draw length, draw stops must be adjusted before the module.
What if my bow draw length is too long?
Many bowhunters shoot a draw length that is too long for them, which hurts shooting form and degrades accuracy. You hear this all the time–that a long draw overextends your bow arm and makes it harder to hold against the back wall and to maintain a consistent anchor point.
Can your draw length change?
Your draw length won’t change at all unless your growing or have a injury. Now from one bow to another it may even in the same line.
Can I shorten my draw length?
To shrink draw length, you need to drop the brace height say 1/4-inch. The way to DROP brace height, is to GROW ATA, so you actually UNTWIST the cables, to grow ATA, which drops the brace height It also advances the cams, which shortens the power stroke. And, drops max draw weight.
Can you shorten bow string?
To increase the string height (distance from the bow to the string), you need to shorten the string. Hold the string between thumb and forefinger, just above the bottom loop. Spin the string between the thumb and finger so that you add twists to it. The more you twist the string, the shorter it gets.
How do you adjust the draw length on a PSE compound bow?
To change draw length on the ECS: Loosen the two 8-32 size 15 Torx® screws holding the module to the cam approximately 1-1/2 turns, move the module to the desired setting. The setting will be in the window marked “DL” move the module to the same setting on both top and bottom cams.
Is longer draw length better?
Since the time always stays the same, we can conclude that the higher the distance (draw length), the greater the speed needed that means longer draw length leads to greater arrow speed and faster arrow.
How long should my draw length be?
Resist the temptation to make your draw length longer than it should be, as this will effect your accuracy. Your wingspan typically is the same as your height in inches; So your height in inches minus 15 and then divided by 2 will be your draw length, or at least a very good starting point.
Does draw length matter?
WHY IT ALL MATTERS Having the right draw length and draw weight for your hunting profile is not just important for performance, but important for safety as well. Also, a longer draw length can force your front arm to a full extension, leaving your inner elbow in direct path of the string and potential injury.
How much does it cost to adjust draw length on a bow?
The changing out of the modules usually requires a hexagonal wrench and can be done without pressing the compound bow. While certain companies will offer lifetime modules changes, most new modules have to be purchased. Average cost is $8 to $25.
Can you shorten draw length by twisting string?
You can also twist or untwist your strings and cables. Twisting the cables an even amount on each side will lengthen your draw length, untwisting them will shorten your draw length. You can twist or untwist the string to adjust draw length, but it won’t quite do as much.
Does a thumb release Increase draw length?
Your release does not alter your draw length. It will affect your anchor point. The reason people increase draw length when switching to a handheld release, is to maintain the normal anchor point, rather than learn a new anchor point.
How does draw length affect draw weight?
Yes, changing to a longer draw length on a bow increases the draw weight. Reduce the draw weight with the oimb bolts if you can. I have done this in the past by using a longer bow string. FOr each inch longer, it added 3 or 4 pounds of weight if I rememebr right.
How do you adjust the draw length on a Browning compound bow?
To change to 30” draw simply remove the screws from the inner cam and move it to the set of holes marked “A” and reinstall the screws. For 28” draw, move the inner cam to the set of holes marked “C”. For 27” draw use the “D” setting. in the set of holes corresponding to the inner cam.
How much can you shorten a bow string?
Shortening the bow string w/ovrhand Knot One over hand knot shortens the string about an 1/8th of an inch. I make the knot about an inch down from the base of the serving of the string loop. Anyone else do this and has anyone also tried this on compound bow strings?Aug 8, 2007.
How do you adjust a bow string?
Bowstrings have twists. Change the brace height by adding or removing twists. To adjust brace height, unstring the bow, remove the bottom string loop, and then twist or untwist the string. If your brace height is too low, give the bowstring two twists to increase the brace height by about ¼ inch.
Do I twist bow string?
Putting in twists will make the string effectively shorter (think about twisting up a piece of string) which will increase the brace height; taking twists out will effectively give you a longer string and therefore smaller brace height. To do the tuning – start with the lowest sensible brace height and shoot 3 arrows.
