Table of Contents
Adjustable cams allow the archer to adjust his or her draw length with the use of an hexagonal wrench without, in most cases, pressing the compound bow. Adjustable compound bow cams allow archers to adjust anywhere from 3 inches up to 13 inches depending on the compound bow.
Can you change draw length without bow press?
All draw length adjustments can be made without the use of a bow press. Draw length changes are made by simply moving the draw stop to the desired position, then rotating the modules accordingly. See draw length settings below. To change draw length, draw stops must be adjusted before the module.
Can your draw length change?
Your draw length won’t change at all unless your growing or have a injury. Now from one bow to another it may even in the same line.
What if my bow draw length is too long?
Many bowhunters shoot a draw length that is too long for them, which hurts shooting form and degrades accuracy. You hear this all the time–that a long draw overextends your bow arm and makes it harder to hold against the back wall and to maintain a consistent anchor point.
What is John Dudley’s draw length?
Overall draw length of 29.125″ has my Stan Shootoff perfect and a tad too long with my TRU Ball HT.
How much does it cost to adjust draw length on a bow?
The changing out of the modules usually requires a hexagonal wrench and can be done without pressing the compound bow. While certain companies will offer lifetime modules changes, most new modules have to be purchased. Average cost is $8 to $25.
How long should arrows be for 29 Draw?
How to: Select the perfect arrow Bow Arrow length Draw weight lb. 25″ 29″ 15-20 700 600 20-25 700 600 25-30 700 500.
Can you shorten draw length by twisting string?
You can also twist or untwist your strings and cables. Twisting the cables an even amount on each side will lengthen your draw length, untwisting them will shorten your draw length. You can twist or untwist the string to adjust draw length, but it won’t quite do as much.
Does a thumb release Increase draw length?
Your release does not alter your draw length. It will affect your anchor point. The reason people increase draw length when switching to a handheld release, is to maintain the normal anchor point, rather than learn a new anchor point.
Is longer draw length better?
Since the time always stays the same, we can conclude that the higher the distance (draw length), the greater the speed needed that means longer draw length leads to greater arrow speed and faster arrow.
Can I shorten my draw length?
To shrink draw length, you need to drop the brace height say 1/4-inch. The way to DROP brace height, is to GROW ATA, so you actually UNTWIST the cables, to grow ATA, which drops the brace height It also advances the cams, which shortens the power stroke. And, drops max draw weight.
How long should my draw length be?
Resist the temptation to make your draw length longer than it should be, as this will effect your accuracy. Your wingspan typically is the same as your height in inches; So your height in inches minus 15 and then divided by 2 will be your draw length, or at least a very good starting point.
How do you measure a bow let off?
Let off is the percentage of draw weight held while the bow is at full draw. Pull the bow down on a scale to just before breakover, this measured value will be the Peak Weight.
What’s let off on a bow?
Let-Off. A compound bow uses cables and cams to store energy and reduce the holding weight at full draw. This reduction in holding weight at full draw is called “let-off,” and is calculated as a percentage of the overall draw weight. For example, a 40-pound bow with a 75 percent let-off would be ten pounds at full draw Apr 6, 2017.
What is 80 let off on a bow?
The most typical “letoff” is 65% but when they were introduced they were 30-40%, then 50% became popular, then 65%, and now bows with as high as 80% letoff can be purchased. The letoff percentage is how much of the draw force is taken off, so a 40% letoff would reduce the peak weight by 40% at full draw.
Does draw length affect arrow speed?
The longer your draw length, the longer your bow’s powerstroke will be – and the faster your bow will shoot. As a general rule, 1″ of draw length is worth about 10 fps of arrow velocity. Bows are IBO Speed rated at 30″ draw length.
What bow size is FOr me?
As a simple rule of thumb bow length should be at least double your draw length, but this doesn’t always correlate to a good decision, so the values in this table should assist.Recurve Draw Length and Bow Size. Draw Length (inches) Bow Size (inches) – AMO 19-21 58 21-23 60-62 24-27 64-66 27-29 66-68.
What pull weight FOr a bow?
Build, Bodyweight and Suggested Bow Draw Weights Type of Person/Build Weight (lbs) Compound Suggested Draw Weight (lbs) Large/Strong Child 100-130 25-35 Small/Slight Woman 100-130 25-35 Average Woman 130-160 30-40 Large/Strong Woman 160+ 45-55.
How much does it cost to get a compound bow adjusted?
A typical bow tuning service costs $40 to $70 and takes about an hour.
How do you adjust the draw length on a PSE compound bow?
To change draw length on the ECS: Loosen the two 8-32 size 15 Torx® screws holding the module to the cam approximately 1-1/2 turns, move the module to the desired setting. The setting will be in the window marked “DL” move the module to the same setting on both top and bottom cams.
How do you adjust the draw length on a Browning compound bow?
To change to 30” draw simply remove the screws from the inner cam and move it to the set of holes marked “A” and reinstall the screws. For 28” draw, move the inner cam to the set of holes marked “C”. For 27” draw use the “D” setting. in the set of holes corresponding to the inner cam.
How do you adjust the draw length on a Genesis bow?
Customizing the Genesis Pro to your draw length is easy! The draw stop on the Genesis™ Pro is adjusted with an Allen wrench. Simply turn the Draw Stop counter-clockwise until it is completely removed; move it to the desired Draw Stop position; tighten until securely in place.
