Table of Contents
How do relays work in KSP?
Uses. Relay Satellites are used to communicate with the Kerbal Space Center without the need for a direct connection to it. Relay Satellites give the function for other Probes to stay connected to the Kerbal Space Center without having the requirement to be in the line of Kerbin, or the range.
What do relay antennas do in KSP?
Relay antennae are able to bounce communications from probes back to Kerbin. If a vessel with a relay antenna has a CommNet connection to Kerbin, then any nearby craft with a connection to the relay vessel will be able to connect to Kerbin through the relay.
What does combinable mean KSP?
CommNet is a relay and control communication system implemented first in KSP 1.2 pre-release. With CommNet enabled (as a difficulty setting), antennae have limited range from which control and transmission of science data is possible.
What is the purpose of satellites in KSP?
Artificial satellites can be used for unmanned flights to test rocket designs, or to travel to other planetary bodies to collect scientific data. With the addition of the career mode and science mode, satellites are not available until later in the game due to the lack of command probes.
What do antennas do in KSP?
Antennae allow communication with Kerbal Space Center, when deployed. With version 0.22 the antennae allow the return of scientific data from space, without the need to recover the craft on Kerbin. Version 1.2 added the requirement of antennae to control unmanned vehicles outside of a specified radius of Kerbin.
What is antenna rating KSP?
Kerbal Space Program For example communotron16 has 500k antenna rating. Antenna rating is how far your antennas are able to communicate. Two 500km rated antennas can only communicate from at most 500km away. Your level 3 tracking station should have a rating of 150Gm or 250,000,000km.
What is Keostationary orbit?
Kerbisynchronous Equatorial Orbit (or KEO for short) is the stationary orbit of the planet Kerbin, a very useful orbit for satellites. A spacecraft on this orbit will appear stationary when viewed from the surface.
What is KerbNet?
KerbNet is an orbital scanning and mapping system introduced in 1.2. When accessed from a KerbNet-capable part, a window will appear, displaying topographic, biome or resource maps for the area under the craft depending on the selected mode and the technical capabilities of the part.
How high is a geostationary orbit in KSP?
The correct altitude is 2,863,334m. You want to start off by getting to a 80km orbit before raising your apoapsis close to the correct altitude, then do a second burn at the apoapsis to circularize. To get an accurate orbit, set the thrust limiter on your engine to 0.5.
How do you use the magnetometer boom in KSP?
Like other scientific instruments, right-clicking on the Magnetometer Boom will reveal an option to “Run Magnetometer Report”. The boom must be extended in order to perform the experiment; if retracted, the boom will automatically extend before performing the report.
What does a relay antenna do?
Relay antennas act as repeaters they retransmit any signals they receive. You can use a chain of relays to send signals across distances too far for any individual antenna. To add to this, it’s not just a distance issue but also a Line of Sight Issue.
What is patched conics KSP?
Patched conics are lines that show your orbit even when you enter a new sphere of inluence. For maneuver nodes you need to upgrade your mission control building, too.
How do you control probe in KSP?
Pilot requirement and comm range While probes will automatically gain control, command pods need to have a capable kerbal (scientist or engineer, not a tourist) in order to gain the ability to create maneuver nodes. SAS is not transmitted, you need to have a probe core with SAS capabilities on the remote ship.
How do I enable Commnet in KSP?
Load the save. Escape menu. Difficult Options. Enable Comm Network.
What is this an engine for ants?
The LV-1 “Ant” Liquid Fuel Engine is the smallest liquid fuel engine available. LV-1 “Ant” Liquid Fuel Engine Radial size Tiny, Radial mounted Cost (total) 110.00 Mass (total) 0.02 t Drag 0.2.
How do you open the cheat menu in KSP?
Press ALT+F12 to access the debug console, which you can use to enjoy unlimited fuel, unbreakable joints, and other helpful perks.
How many planets are there in Kerbal space program?
The Kerbol System consists of six planets that may be orbited by moons and/or asteroids. Each of these bodies exhibits its own characteristics like gravity, atmosphere, size, orbital inclination, and orbital period.
How do you change the difficulty in KSP?
Game Difficulty can be accessed when starting a new save file by clicking on the Difficulty icon on the lower-left of the New Game screen. There are four different presets available, as well as the option to set up Custom difficulty options.
What does the Stayputnik do?
The Stayputnik offers the ultimate solution in crew safety. A lightweight sphere equipped with remote receivers and relay control input from the ground to the craft, it carries no crew at all, thus keeping them perfectly safe from all harm.
What are probes for KSP?
Probes are craft whose command modules have zero crew capacity, modules generally known as “probe cores”. Probes can perform missions and can often more easily reach places that manned vessels either cannot reach or cannot return from (at same cost or tech level).
How do you do a Keostationary orbit?
1: Get into a circular orbit at 871 km. 2: When over the required spot, burn to increase apoapsis to your final target. This orbit should have a period of 216 minutes. 3: Wait till you’ve made 2 full orbits and are approaching apoapsis for the 3rd you should be right on top of your target point.
