Table of Contents
A: It’s perfectly acceptable to put tile directly on concrete — with a couple of caveats. First, it is important to determine if there is moisture coming up from the slab. Those products should help prevent any cracks in the slab from damaging the newly installed tile.
Can ceramic tile be installed over a sealed concrete floor?
Attaching any tile product to sealed concrete is strongly advised against without first removing the sealer. The unmodified thinset would be the recommendation for use ON TOP of the DITRA when porcelain tile was used. DITRA is in fact a crack membrane but really isn’t intended to SOLVE any moisture problems.
Do I need to seal concrete before tiling?
You need to clean any paint, sealant or glues from the surface of the concrete. Concrete sealant or paint prevents the adhesive from sticking properly. Let the surface of the concrete completely dry before installing tile.
Can you lay tile directly on concrete?
A: It’s perfectly acceptable to put tile directly on concrete — with a couple of caveats. First, it is important to determine if there is moisture coming up from the slab. Those products should help prevent any cracks in the slab from damaging the newly installed tile.
How do you prepare a concrete floor for tile?
Preparing Cement for Floor Tile Clean. Start by sweeping your concrete floor to get rid of all dust and debris. Then clean with a wet mop of plain water. Dry. Ensure your floor has thoroughly dried before proceeding. Level. Use floor leveling compound for large holes or flaws in your cement floor.
Can you put flooring over sealed concrete?
While concrete sealer may appear dry, it cures slowly over time. It is best to wait several weeks after application before installing your tile.
Do you need a moisture barrier under ceramic tile?
During patching, most people usually wonder if they would need a moisture barrier under tiles. Well, yes. A moisture barrier should be installed to protect the flooring against moisture or moisture vapor.
How do you remove sealer from concrete?
Start by removing any visible peeling and flaking and use a solvent based stripper such as Xylene to remove the previous sealer. (If concrete was dyed or stained, using Xylene can damage or change the color of the concrete.) Pressure wash the surface and allow concrete to completely dry.
What to use to seal concrete floor before tiling?
There are specific preparation requirements for anhydrite screed – assuming these have been done, you will then need to use a good quality acrylic primer to seal the floor. Two coats will be required at 90 degrees to each other i.e. one coat one way across the room and another coat the other way.
What do I put on concrete before tiling?
You can install a CBU or cement board on the concrete, then the tile on top of that. Finally, you can use an uncoupling membrane between the tile and the concrete.
Do I need to PVA a concrete floor before tiling?
Short answer. No, never use PVA to prime a surface before applying tiles. The acetic acid produced when cement and PVA come into contact would render the adhesive and grout useless.
Does mortar stick to concrete?
Concrete slab was the foundation, original tile installation had mortar applied directly to concrete slab. Concrete, mortar or similar materials are not designed to stick or bond to old surfaces. You will not get any satisfactory results if you simply add new mortar to old.
What kind of Thinset do you use for concrete floors?
Modified thinset is the product of choice for most tile installations because of its increased strength and bonding with minimal shrinkage, which means a reduced chance of cracks forming in the tile. WarmlyYours Radiant Heating recommends modified thinset mortar for nearly all tile and stone installations.
Do you need underlay for vinyl flooring on concrete?
Do you need underlay for vinyl flooring on concrete? If the concrete floor is level and clean, vinyl underlay is not a necessity, but because of noise reduction and other qualities of underlay, it is worth considering. If the concrete floor is uneven it will need levelling.
Do I need a vapor barrier under tile flooring?
A moisture barrier helps control the water vapor’s movement to help protect your floors. Therefore, if you’re installing floors in an area that sees moisture, even a little, a vapor barrier is needed.
Can you tile over a damp floor?
Short Answer: Yes, you can tile a damp basement if it’s rising damp, but it’s very important to use breathable tiles, such as unsealed quarry tiles or natural stone tiles that have been treated with a water-based sealer, such as LTP Mattstone H2O.
Does tile need an underlayment?
Tile may be strong, but it needs a solid, supportive base. An underlayment is the solid stabilizing layer directly below the tile and the tile adhesive (usually a thinset mortar). Using the wrong one can spell disaster for your tile installation. These poor tiles were installed improperly; they never stood a chance.
Will vinegar remove concrete sealer?
Can You Remove Concrete Sealer With Vinegar? It is possible to remove concrete sealer using vinegar for a safer alternative. However, vinegar will not be as effective as an acrylic concrete sealer remover. We recommend using made-for-purpose chemical strippers to get the job done most effectively.
Does power washing remove concrete sealer?
A pressure washer can remove old concrete sealers. The sealer can be removed from concrete by using a pressure washer with a wand or an orbital walk-behind model. Keep in mind, however, that even though this method is effective, it may not completely remove the old sealer.
How do you waterproof a floor before tiling?
To make the floor waterproof, seal the seams and floor-to-wall junctions with a waterproof tile membrane. Spread mortar over the seams, comb it, and press the band over it. You want a 2-inch overlap at all seams.
Can you use SBR as a primer for tiling?
A multi-use synthetic polymer primer and admixture, BAL Bond SBR can be used as a bonding agent for adding to mortars used in screeding, plaster, rendering, bricklaying, pointing and repairs and as a primer for tile fixing onto timber, plaster, screeds, rendering or vinyl tiles.
Should I PVA before tiling?
No, you should never use PVA to prime a surface before tiling. PVA (Polyvinyl Acetate) is often used to seal things, or used as a glue in crafts and woodworking but should not be used as a sealer before tiling.
Can I use PVA to seal concrete floor?
Concrete sealers are designed to prevent these problems, and a sealer that contains polyvinyl acetate — PVA — can be especially effective. A PVA sealer can also provide an adhesive undercoat for new concrete. You apply it with a paintbrush after thoroughly cleaning the concrete.
Can I use PVA as primer for self Levelling compound?
Make sure you use a proper tiling primer PVA isn’t to be used as a primer. Get an acrylic based primer. Defending how high you need to go I either cut a length of timber and wedge it in the doorframe to stop the compound leaking.
