Table of Contents
Tile can be laid on plywood. But do not install tile directly on the plywood subfloor itself. Use an intervening layer of a sheet of thinner plywood.
What kind of subfloor is needed for ceramic tile?
Exterior-Grade Plywood Exterior plywood is an acceptable underlayment for tile and is preferred to interior-grade plywoods because the bonding adhesives used are waterproof. If water seeps through the tile installation to the underlayment, it will not cause the wood to swell, as happens with interior-grade plywood.
Does a plywood subfloor have to be 100% level for installing ceramic tile?
Before installing tile on your floor you must make sure your floor is properly prepared. A properly prepared floor does not have to be level.
Can you tile directly to subfloor?
While you can lay tile directly over a concrete slab using thin-set adhesive, don’t make the mistake of applying tile directly to a plywood subfloor. No matter how firm the subfloor; the plywood will expand and contract at a different rate as the tile, causing cracks to develop in the grout lines or tiles over time.
Do I need to seal plywood before tiling?
This expansion gap should be filled with a silicone sealant to prevent it from being filled with tile adhesive when fixing your tiles. Before fixing your plywood overlay, ensure the reverse and edges of the boards have been sealed using BAL Bond SBR neat, as this reduces water permeability.
What is the minimum subfloor thickness for ceramic tile?
The subfloor under the tile should be at least 1 1/8″ thick, with a minimum of 5/8″ thick exterior grade plywood topped by 1/2″ cement backer board.
What kind of plywood do you use for tile subfloor?
Tip: Make sure the subfloor will not deteriorate when it gets wet. Particleboard is not an acceptable subfloor material for tiling projects. Oriented strand board (OSB) and exterior-grade plywood will work if first covered with a latex-modified mortar and a tiling backer board.
What is the best subfloor for porcelain tile?
1. Backer Board. This is the industry standard most preferred by construction pros when installing ceramic or porcelain tile. Backer board comes in four-foot-by-eight-foot and three-foot-by-five-foot rigid panels that contain a combination of cement, fiberglass, and sometimes crushed glass particles.
How level does the floor need to be for tile?
As noted in the first answer above, the surface to be tiled, in your case the floor, must be flat within 1/8” in 10′ when measured from the high points of the floor. To achieve this, be sure to use the appropriate patch or self-leveling compound (with the same manufacturer’s primer), but never thin set mortar.
How uneven can a floor be for tile?
As a general rule the floor needs to be almost perfectly flat. When the underside of the tile is uneven it’s difficult to get enough glue coverage. And the recommended glue coverage for indoor tiles is around 80%. Any less than that and the tiles become damaged very easily.
How smooth does subfloor need to be for tile?
A subfloor is the bottom-most structural level of your floor. A good subfloor needs to be durable, level, at least 1 ⅛ inches thick, and free from residue. If it is not, it won’t support tile well. Even the smallest cracks or depressions in a concrete floor could cause your tile to break early.
Do you need underlayment for tile floor?
Some people usually ask themselves if porcelain tiles need underlayment, well yes, they do. For your porcelain tile to last for long, you need an underlayment. Both porcelain and ceramic tiles are rigid, so if they are installed on surfaces that are not flat, they can crack easily.
Do you need backer board for floor tile?
Whenever you’re laying tile on a wood subfloor, you need to first install cement backerboard to prevent leaks and water damage that could harm your flooring and the structure of your home. Unlike wood or drywall sub-surfaces, cement backerboard will not rot, warp or grow mold and mildew when exposed to water.
Can you lay tile directly on OSB?
You can lay tile over an OSB subfloor, but a membrane should be installed between the subfloor and the tiles to ensure a bond between the tile and the floor is made. Even if you are looking for a new subfloor to install, OSB is inexpensive and can work well with tile.
Can I put floor tile directly on plywood?
Tile can be laid on plywood. But do not install tile directly on the plywood subfloor itself. Use an intervening layer of a sheet of thinner plywood.
How do you seal plywood before tiling?
Plywood requires the application of a latex based bonding solution to the plywood to seal it and then the use of a flexible cement based adhesive, not pre-mixed tub adhesive.
Can you use thinset to level a plywood floor?
Because mortar will stick to the concrete slab and the wood subfloor, and mortar will stick to mortar, then it would only make sense that mortar would work for leveling or patching, right? Well, the answer is actually no. Mortars cannot be used to level or patch a floor – ever!Aug 3, 2020.
Can I tile directly onto wood?
Tiling on wood. Can you tile on wood? Yes, but because wooden floors naturally bend, bounce and expand, tiles can end up cracking under the pressure if installed incorrectly. Tiling on wood surfaces is all about ensuring there is enough rigidity in the wooden subfloor and selecting the correct flexible tile adhesive.
Can you tile on 6mm plywood?
6mm No More Ply is a pre-primed tile backer board which provides a flat, stable surface ready for floor tiling. The 6mm depth of the boards means there is minimum disruption to the height of the floor, so as to not cause too much of a height difference between adjoining rooms.
Is 3/4 subfloor enough for tile?
Tile installed over wood floor systems MUST have a minimum of 1-1/4 inches of solid material beneath it. This means you can have a 3/4 inch wood subfloor covered by 1/2 inch plywood, cement board, or approved gypsum fiber underlayment.
How thick should plywood be for a tile floor?
You’ll need to cover your floorboards with a rigid and smooth surface to prepare it for tiling. Traditionally, 12mm thick plywood was the way to go, but this can raise the floor height of the room by around 1.5cm once tiled.
How thick should plywood be for tiling?
When using plywood, you’ll need to ensure it’s at least 12mm or more in thickness to create a rigid surface for your tiles. This, along with your tiles, will raise the level of your flooring, so be sure to bear this in mind before you get started.
What thickness plywood should I use for bathroom flooring?
Consider what the top layer of the bathroom flooring will be since some types of plywood are better suited for different flooring. For hardwood, tongue-and-groove CDX plywood rated AC with a 1/2- to 3/4-inch thickness is best. Specifically for subflooring, tongue-and-groove plywood is strong and will reduce squeaks.
What do you put down before you lay tile?
Underlayment is something you put on top of your substrate to prepare it for tiling. The substrate (or subfloor) is the ground, whether it’s made of plywood or cement. Cement board or backer board are the most standard underlayments.
