Table of Contents
Can you tile over patio slabs?
Yes, you should lay the tiles to a fall, 1 in 40 is about right but you could go more or slightly less than this. Question about DPC is very relevant. You should have 150mm (6 inches) from top of new paving to DPC. If you can’t achieve this then probably best to take up the old slabs and possibly the sub base also.
Can you put tile on subfloor?
Tile can be laid on plywood. But do not install tile directly on the plywood subfloor itself. Use an intervening layer of a sheet of thinner plywood.
Can you tile on bitumen floor?
You can tile immediately on to contaminated, stained or cracked screeds and over bitumen. Roll out the BAL Flexbone 2Easy with the blue mesh side up. Roll out from the corner and cut precisely to the required length and sizes as required for the floor.
Can you tile over cutback adhesive?
If it is cutback, you can still install tiles on that floor with a little prep. You’ll need to remove the cutback until only a film is left. In other words until you start to see the concrete. You’ll need a wallpaper scraper which has a razor cutting edge and several hours of your time.
Can you tile over outdoor pavers?
Give outdoor areas a speedy modern makeover with easy-to-lay timber tiles. Updating tired concrete, pavers or pebblecrete used to be a big hassle. The tiles are tolerant of wet areas, so you can use them as part of an outdoor shower.
What kind of subfloor is needed for ceramic tile?
Exterior-Grade Plywood Exterior plywood is an acceptable underlayment for tile and is preferred to interior-grade plywoods because the bonding adhesives used are waterproof. If water seeps through the tile installation to the underlayment, it will not cause the wood to swell, as happens with interior-grade plywood.
How thick does the subfloor need to be for tile?
The subfloor under the tile should be at least 1 1/8″ thick, with a minimum of 5/8″ thick exterior grade plywood topped by 1/2″ cement backer board.
What will stick to bitumen?
Where it’s wanted for something to stick to bitumen, sand is sprinkled on while still wet. Cement, paints etc can then stick to the sand.
Can you lay tiles over tarmac?
ideally without having to concrete over it. Presuming you mean paving slabs Mo, yes its usually ok. The slabs should be laid on a bed of sharp sand and cement approx 50mm thick and mixed at 8 to 1.
Can I lay screed over bitumen?
because a latex based screed should never ever be used over Bitumen, the green colouring may be due to a chemical reaction between the two substrates which will require the screed to be mechanically removed.
How do you cover cutback adhesive?
The Cutback Adhesive can be covered with a cementious patch or self leveler, or use the Triseal and an adhesive for vinyl that can be used dry to the touch.
Do I need to remove adhesive before tiling?
Installing ceramic tile requires a smooth, level substrate surface for the material to properly bond. To install the new tile properly, you must first remove all traces of the adhesive to provide an ideal surface to attach the tile.
Can I tile over old mastic?
As long as the mastic is generally smooth (no ridges between the old tiles) it will go down just fine.
Can you lay tile over brick pavers?
When more color or personalized style is desired, however, tiling over exposed brick can be a great way to bring a whole new look to the space. Glass tiles, ceramic tiles, porcelain tiles or natural stone tiles can all be laid over brick to give a space a fresh, updated appearance.
What can you put over pavers?
What Do You Put Between Pavers to Make Them Stable? Base Layer. Create a strong base for pavers with a layer of porous material, such as gravel or crushed rock. Sand Bedding. The sand should be firm and feel much more solid once you’ve tamped it in place. Sand Between Pavers.
What do you put on top of pavers?
Polymeric Sand is a blend of sand and special additives designed to fill the joints between concrete pavers and brick pavers.
Can you lay tile directly on concrete?
A: It’s perfectly acceptable to put tile directly on concrete — with a couple of caveats. First, it is important to determine if there is moisture coming up from the slab. Those products should help prevent any cracks in the slab from damaging the newly installed tile.
What is the best tile adhesive for outdoor use?
10 Best Tile Adhesive For Outdoors Evo-Stik. Evo-Stik Tile a Wall Adhesive & Grout for Ceramic & Mosaic Tiles 1. Everbuild. Everbuild 702 Water Resistant Tile Adhesive, Off White, 7.5 kg. Blulu. 100 Pieces Mini Outdoor Cable Clips with Adhesive Tapes Light Clips Decoration Clips. Unibond. POLYCELL. Unibond. YOLETO. Everbuild.
Do I need to seal plywood before tiling?
This expansion gap should be filled with a silicone sealant to prevent it from being filled with tile adhesive when fixing your tiles. Before fixing your plywood overlay, ensure the reverse and edges of the boards have been sealed using BAL Bond SBR neat, as this reduces water permeability.
Do I need backer board for floor tile?
Whenever you’re laying tile on a wood subfloor, you need to first install cement backerboard to prevent leaks and water damage that could harm your flooring and the structure of your home. Unlike wood or drywall sub-surfaces, cement backerboard will not rot, warp or grow mold and mildew when exposed to water.
Can you wall tile onto plywood?
If you are working in an interior setting in a dry area where the tile will never come into contact with water, you can install the tile directly onto the face of the plywood so long as you use the proper type of thinset.
