Table of Contents
You can also fine-tune your bows draw length by increasing or decreasing the size of your D-loop. You can also twist or untwist your strings and cables. Twisting the cables an even amount on each side will lengthen your draw length, untwisting them will shorten your draw length.
Can you shorten a bows draw length?
Adjustable cams allow the archer to adjust his or her draw length with the use of an hexagonal wrench without, in most cases, pressing the compound bow. Adjustable compound bow cams allow archers to adjust anywhere from 3 inches up to 13 inches depending on the compound bow.
How much can you twist a bowstring?
Question: How many twists can be put into a bowstring? On a standard compound bow, initially 1/2 to 3/4 twists per inch is a suggested range; meaning on a 60″ string, you should apply 30 to 45 twists. If you use a material that does not creep, no further twisting will be required.
What does twisting a bow string do?
Putting in twists will make the string effectively shorter (think about twisting up a piece of string) which will increase the brace height; taking twists out will effectively give you a longer string and therefore smaller brace height. To do the tuning – start with the lowest sensible brace height and shoot 3 arrows.
Can you shorten bow string?
To increase the string height (distance from the bow to the string), you need to shorten the string. Hold the string between thumb and forefinger, just above the bottom loop. Spin the string between the thumb and finger so that you add twists to it. The more you twist the string, the shorter it gets.
How do I know if my bow draw is too long?
The bow arm should move toward the target when the shot is fired. If the bow arm drops or swings to the side, the draw length is probably too long. When this happens, the scapula has already pushed the bow arm out as far as it can extend before the arrow is released.
How many strands should my bow string have?
The most commonly used number of strands is 12 strand B50 string , which provides a balance between size, weight, strength, and nock fit. Bigger 14 strand B50 strings are mostly used on heavier bows as well as where the extra weight of the bowstring acts as a slight damper to make shooting more consistent.
What is a Flemish twist bow string?
A Flemish twist has braided loops on each end that give it a beautiful, traditional look. An endless-loop bowstring has loops formed by wrapping serving material, which is a braided string, around the bowstring.
Where should my draw length be?
To measure your draw length, stand with your back to a wall stretching your arms out against the wall. Measure the distance from the end of your middle finger to the end of your other middle finger, basically the length of both arms, hands and chest. This measurement, minus 15 then divided by 2, is your draw length.
Is a longer draw length better?
Since the time always stays the same, we can conclude that the higher the distance (draw length), the greater the speed needed that means longer draw length leads to greater arrow speed and faster arrow.
Does twisting cables increase draw weight?
You don’t get more poundage by twisting the cables and strings. You gain it by twisting the cables, which increases the poundage and the draw length.
How many times should you twist a recurve bow string?
on average 12-15 twists is good in a string .. gives it a nice round feeling when you slide your fingers up and down it with eyes closed.. this is just and average.. 51 twists is way to many when you unstring your bow the string must look like a coil spring.
How do you shorten an axle compound bow?
Twists will shorten the axle-to-axle. Taking off twists will lengthen it. Finally, check the brace height by measuring from the deepest part of the bow’s grip to the string. If it’s off, add or remove twists from the string.
Does a shorter draw length affect arrow speed?
With more potential energy in the drawn bow, there will be more kinetic energy in the released arrow – more arrow speed. As you lengthen your draw you must go to a longer and stiffer arrow for the same maximum draw weight.
What is the average draw length on a bow?
If you have an average draw length of 27 to 29 inches, any modern compound bow matched with a good arrow and set to 60 pounds will work just fine on whitetails, mule deer, pronghorns, and the like with whatever broadhead style you prefer, so long as your shot placement is good.
Does draw length matter?
WHY IT ALL MATTERS Having the right draw length and draw weight for your hunting profile is not just important for performance, but important for safety as well. Also, a longer draw length can force your front arm to a full extension, leaving your inner elbow in direct path of the string and potential injury.
Will a new bow string stretch?
It’s not uncommon on new bows to see stretching or creeping. The issues that bow string stretch brings oftentimes will extend beyond the normal peep and point of impact problems. Your draw length, draw weight, holding weight, cam synchronization and tune can change and you never know when it will happen.
What happens when bow string stretches?
Are Bowstrings Supposed to Stretch? Bowstrings are not intended to be elastic (stretchy). The power of the bow comes from the limbs. Anything else that stretches, like strings, will absorb the power from the shot instead of putting that energy into the arrow.
Should you wax bow string serving?
Step 1. Apply wax directly along the length of the string (and cables) by rubbing it up and down wax is visible along the length of the strands. Do not wax the serving. It’ll unravel quicker – and also make it slippery!Aug 25, 2016.
When should I replace my bow strings?
Like most bow companies, we recommend changing bow string and cables once a year on target bows and every two years on hunting bows. Target bows require more frequent restring since they see more shooting than a comparable hunting bow.
