Table of Contents
How long does it take a 68RFE to relearn?
Registered. It should only take 30 miles of stop and go driving to relearn at 30% or less throttle. Use the power setting you’re going to drive it on.
Can you switch tunes with autocal?
You’ll have to buy a new autocal. Your current one is licensed to the v2 that tuned it.
How do I reset my Dodge transmission?
I believe it’s also possible to reset the TCM by cycling to the run position without pressing on the brake pedal. Then slowly depress the gas pedal to the floor and let it back up. Afterwards, cycle to the off position. When you restart, it should be reset.
Can you tune a 68RFE transmission?
68RFE automatic transmission equipped trucks, you have the option to add transmission tuning. For the 68RFE (if you have a 68RFE we highly recommend the trans tuning for the longevity of making your transmission last at higher HP and TQ) , if you dont know what trans your truck has its simple to find out.
What is EFI Live AutoCal?
EFILive’s AutoCal device is intended to provide a convenient platform for professional tuners to distribute custom tunes to their customers. And for their customers to collect and submit logged data back to the tuner for analysis.
Can EFI Live read codes?
With efi live deletes there will be no codes, emission components get turned off, or removed from the trucks brain. Just make sure to tell your tuner exactly you want done.
What is a DSP5 switch?
The CSP5 and DSP5 switches allows users to switch on the fly between 5 user defined tunes. With the DSP5 switch, you can change your tuning “on-the-fly”. Tuning not included, you must have DSP5 Tuning for use with this switch.
How long does it take for an Allison transmission to relearn?
Re-learn normally takes up to two hours (this time can be significantly reduced by using Tech2 or PC based Allison software to clear the memory and place the TCM in the ‘fast learn’ mode). During the relearn there will probably be some clunks, bumps and/or short flares, especially during the 3-4 shift. This is normal.
How do I reset my Allison transmission?
Allison Transmission Transmission Service Indicator Light Reset To reset the service indicator light. Turn the key on, do not start the engine. Move the shift selector to N-D-N-D-N-R-N, pausing briefly (less than 3 seconds) between each selector movement.
How long does it take for a transmission to relearn?
Any time a battery is disconnected, or in your case a transmission is replaced, it can take up to 90 days for the engine and transmission computer to relearn your driving habits. It’s normal for an automatic transmission not to shift into higher gears until the engine coolant temperature is at a specified temperature.
What is quick learn on transmission?
Any time a major repair is done on this transmission or the transmission is rebuilt or replaced, a relearn procedure must be performed. This procedure is called “Quick Learn”. Failure to relearn the computers shift settings can lead to gear train failure and void the warranty on your remanufactured transmission.
What does it mean to relearn transmission?
Computer Transmission Shift Adaptive Relearning On these transmissions, the timing of the release and application of elements (clutch packs and bands) is controlled by the transmission control module (a microprocessor). As the transmission shifts gears, one element is released as another is applied.
What is TCM tuning Cummins?
TCM (Transmission Control Module) Tuning that will deliver 2nd Gear Lockup and a modified shift schedule to promote longer transmission life and a firmer shift under engine load so you’re getting more power to the ground. TCM tuning is only available for Rams equipped with the 68RFE transmission, not the Aisen.
How do you reset a transmission control module Dodge?
The way you do this depends on what model year car you have. You can disconnect the negative terminal of your battery, and then let it sit for 15 minutes (always longer than recommended for good measure), and then hook it back up, and it should reset the module.
How do you reset the transmission control module on a Dodge Ram?
If you are looking to “reset” the module just disconnect your battery for 30 minutes or so. Your TCM will be back to default and it will start ‘learning’ again from square one.
How do you reset a transmission control module?
Steps to Resetting Transmission Control Module Step 1: Turning Key Position. Step 2: Press gas pedal. Step 3: Keep Waiting. Step 4: Turning the Key Off. Step 5: Releasing Gas Pedal. Step 6: Wait Again. Step 7: Ready. Identification.
How much power can the 68RFE handle?
With quality transmission control module (TCM) tuning, the stock 68RFE can support 500rwhp and 1,000 lb-ft or more, but it won’t survive boosted, four-wheel drive launches for very long—and maybe not even once if the Low/Reverse sprag explodes (which is common).
How much horsepower can a stock 68RFE transmission handle?
Dodge Transmissions: TF727 to 68RFE Even a stock transmission with a bump in line pressure or a shift kit (something that can be performed by any transmission shop) will be able to handle 300 to 400 hp at the wheels if it’s in good shape.
How does a 68RFE work?
The 68RFE pressure control sys- tem monitors input torque and adjusts the pressure accordingly. The primary stage of the pump works continuously; the second stage is bypassed when demand is low.
What is the difference between FlashScan and AutoCal?
With FlashScan V2, end users have the ability to create, view, and modify tunes. AutoCal is limited to flashing tunes provided by a single tuner. FlashScan is required to create tunes for an AutoCal device. AutoCal devices cannot create tunes.
Does EFI Live tune transmission?
OK, EFI Live does not do delete tuning, Does not do transmission tuning, or any tuning for that matter other than a base file for emissions compliant. It is simply a tool. A custom tuner takes care of the rest.
