Table of Contents
Are Filter Balls Better Than Sand? Pool filter balls are much more effective at clearing the water than sand because they can trap particles that are as small as 3 microns. That means you will have clearer, cleaner pool water in almost half the time with a lot less work needed from your pool pump and filter system.
Do filter balls work in a sand filter?
Platinum Filtra Balls are a light weight filter media that can replace the silica sand inside of your sand filter system. They are reusable, eco-friendly and made from 100% polyethylene.Sand Filter System – Filtra Ball Requirements. Filter System Boxes Of Filtra Balls Hayward S210T 20″ Sand Filter System 4 Boxes.
How often do you have to clean pool filter balls?
Typically, cartridge filters need to be cleaned every two to six weeks. One of the most important factors that affect a cartridge filter operating effectively is that there not be too much flow through the filter.
What is the best media for a pool filter?
Glass Pearls are one of the most effective pool filter medias available today. Furthermore, glass extends the operation times and reduces the frequency of backwashing, saving you time and water (up to 20 per cent less water is used in the backwashing process).
How do filter balls work?
FilterBalls are engineered to get more water flow from lower pump speeds, allowing your pump to work more efficiently, using less power. Slower water velocity (not higher) is the key to better filtration. With your single speed pump, your flow will increase and clean more water with every kilowatt of power.
Can filter balls be washed?
You can easily clean your filter balls using a washing machine. Just put them in the machine and make sure that they have no soap residue left on them before returning to your pool. Otherwise, it can cause an undesirable bubbling effect for you while swimming.
Can I backwash filter balls?
It is recommended you open your filter tank and rinse / clean off your Filtra Balls once per month to ensure they continue to filter properly – backwashing may not fully remove debris from Filtra Balls.
What happens if you don’t backwash your pool?
Backwashing can result in a loss of water. While this is unavoidable, you can minimize the amount of water you lose by not overdoing the backwashing process. Keep a close eye on the color of the water through the view glass and stop the minute it becomes clear.
Can you backwash a sand filter too much?
If you backwash your pool too much i.e. time duration and/or close frequency then yes you can cause a lot of problems. Some problems that can arise from backwashing your sand pool filter too much are: Loss of water – 500+ litres of water can be lost in each backwashing cycle.
Does backwashing remove water from pool?
The backwashing process reverses the flow of water to flush out contaminants from a swimming pool filter. It should be carried out until water runs clear through the waste line.
How often should you change sand in pool filter?
On average, sand should be replaced every 3-5 years. This may be longer if the pool stays clear, or shorter, if the filter runs all the time. The jagged edges of the sand wear down and become smooth as the sand ages.
Can you put too much sand in a pool filter?
Too much sand and your filter will likely not run correctly or may break when reassembling. Too little sand and you will have cloudy water no matter how much your filter runs. Typically filters hold sand in 50 lb. increments, so you can safely expect filters to range from 100, 150, 200, 250 lbs., etc.
How do I know if my sand filter is bad?
If you’ve noticed that the backwashing cycles have become shorter, then you should check to see if the sand filter is dirty or greasy. If the filter is dirty or greasy, then don’t be surprised if it takes on the appearance of sandy lard. When this happens, the water doesn’t flow through the sand filter media.
Can I use a clarifier with filter balls?
This product has recommendations for certain chemicals to be used with them NEVER USE POOL CLARIFIERS it will clog the balls and cause all sorts of problems so check that first, next check your pool equipment that it is all functioning properly it’s probably a matter of one or the other is the problem.
How much sand goes in a pool filter?
How Much Sand to Add to Pool Filters? Sand filters are not filled completely full of sand, but only about 2/3 full, to allow “Freeboard” space in the tank, above the sand bed.
How many bags of sand do I need for my pool?
How Much Sand Will I Need For Pool Installation? Amount for Sand Base with SAND COVE Amount for Sand Base with FOAM COVE Pool Size Yards of Sand Tons of Sand 12′ Round 1.00 1.00 15′ Round 1.50 1.50 18′ Round 2.00 2.00.
How often replace pool filter media?
If your pool filter is extremely undersized, you may need to change it every year. However, assuming proper sizing, “they say” that filter sand will last 7-8 years, filter cartridges 3-4 years and DE grids should last around 10 years.
How much is a zeolite sand filter?
You only require half as much zeolite as your normal silica sand. If your filter requires 300 lbs of silica sand, you only need 150 lbs of zeolite.
How do you backwash a pool filter?
How to Backwash a Pool Sand Filter Turn off the pool pump. Set the filter valve handle to the ‘Backwash’ position and ensure the handle locks in place. Turn the pump on and backwash for 2 minutes or until the water in the sight glass (located on the filter) is running clear. Turn off the pump.
What do bio balls do?
Bio balls are used to hold the beneficial bacteria from your tank and not for removing waste products from the system. We recommend that these are used after the water flows through filter foam as the foam will catch and remove any debris from the water meaning these will not get stuck in the groves of the Bio balls.
What is backwashing a pool?
Well, as the name suggests, backwashing involves reversing the flow of water through your filter media, be it Zeoplus, sand, glass pearls or diatomaceous earth (DE). This dislodges dirt and debris that may have become trapped, and flushes it out through your multiport valve waste line.
