Table of Contents
How are cabinet dimensions written?
The industry standard is to list the width, the height and then the depth.
How do you read cabinet drawings?
For instance, on a kitchen floor plan, you will typically see a base cabinet labeled SB36, B30, 3DB24, and W2442. What the nomenclature above means: SB36 = SB stands for Sink Base and 36 means the cabinet is 36” wide. B30 = B stands for Base and 30 means the cabinet is 30” wide.
How are cabinets measured?
Finding the Measurements of Existing Cabinets. Find the total height and depth of each cabinet. Using a tape measure, determine the height of each cabinet from base to tip and the depth of each cabinet from front to rear. For accuracy, figure out the depth by measuring from the outside of each cabinet, not the inside.
What is the proper order of drawings in a construction set?
Drawings are always organized from most general to most specific or specialized. Since plans are most helpful to see the overall design of the project, they come first. Elevations and sections are a bit more specific and come next followed by details and schedules, which are the most specific type of drawings.
What are the dimensions of a kitchen cabinet?
Base Cabinet Height, Depth, and Width Height, without countertop 34 1/2 inches Height, with countertop 35 to 36 inches Depth (front to wall), without countertop 24 inches Depth, with countertop 25 to 26 inches Standard widths 12, 18, 24, 30, 33, 36, 48 inches.
What are standard kitchen cabinet dimensions?
Standard kitchen cabinet heights include 12, 15, 18, 30, 36 and 42 inches tall; depth ranges from 12 to 18 inches. Typically installed 18 inches above countertops, 54 inches above floor and 24 inches above stove.
What is a cabinet drawing?
Definition of cabinet projection : an oblique projection in mechanical drawing in which dimensions parallel to the third axis of the object are shortened one half to overcome apparent distortion.
Do architects design cabinets?
Architects and interior designers who draw kitchens and don’t actually sell cabinetry usually equate success designing a kitchen with giving customers “bigger and more”. However, most experienced kitchen designers generally spend a lot of time persuading clients to get LESS cabinetry and leave more space!.
How do you describe kitchen cabinets?
Kitchen cabinets are the built-in furniture installed in many kitchens for storage of food, cooking equipment, and often silverware and dishes for table service. Appliances such as refrigerators, dishwashers, and ovens are often integrated into kitchen cabinetry.
How do you size cabinets?
Measure the cabinet opening: Measure in the same fashion as for a single door, getting the total width and height from the inside edge of the cabinet opening. Add space for door overlay: Add 1 inch to the height of the opening. For the width, add 1 inch to your total width and then divide by 2.
What are the 6 types of construction drawings?
What Are the Six Types of Construction Drawings? Plans. Interior and exterior elevations. Building and wall sections. Interior and exterior details. Schedules and room finishes. Framing and utility plans.
What do construction drawings look for?
A complete set of house plans usually contains floor plans, elevations, sections and “details” that together form a detailed picture of the entire house. There is often a separate page for each major trade, including a site plan, floor plans, foundation plan, electrical plan, plumbing plan, and framing plan.
Which drawing would show landscaping?
A civil drawing, or site drawing, is a type of technical drawing that shows information about grading, landscaping, or other site details.
What is the standard cabinet depth?
As far as depth goes a standard base cabinet is 24 inches deep. For islands or other areas where there isn’t enough space for such a deep cabinet, the size is generally reduced by three inches at a time. The shallowest base cabinets are 12 inches deep (Usually a wall cabinet is used to achieve this depth).
How wide are kitchen drawers?
Standard non-custom kitchen cabinetry generally offers drawer widths from 12 inches to 24 inches, increasing by 3-inch increments. If the standard drawers available don’t fit into your kitchen design, you can order custom drawers from a cabinetmaker.
What is the depth of a kitchen cabinet?
Standard base cabinet depth is 24 inches (61cm). Deeper cabinets are also available and are useful because refrigerators have been getting deeper – up to 36 inches deep (92cm) so a deeper countertop is appropriate.
How much space should be between upper and lower cabinets?
The standard distance between the top of a kitchen counter and the bottom of the wall cabinets above it is 18 inches. For the average person, this distance is the ideal balance between plenty of space to work on the countertop and the ability to reach all of the shelves in the cabinet.
What size cabinet goes over a stove?
Clearance for Safety As you plan the sizing of upper cabinets, allow 30 inches of space between the bottom of the cabinet and the cooktop of an electric stove. Gas stoves require a 36-inch clearance. The bottom of your overhead cabinet with the range hood installed should be 66 to 72 inches from the floor.
How do you measure cabinet width?
Lay the tape measure along the bottom of the cabinet; place the end against the back of the cabinet, then pull out the tape until the front edge of the cabinet to find the front-to-back (depth) measurement. Next, measure the total outer width of your cabinet.
What is the difference between the Cavalier and Cabinet drawing?
For a cavalier oblique, the depth of the object is drawn to full scale. For the cabinet oblique, the depth is drawn to a length of half of the actual depth measurement.
What depth is a Cabinet drawing in an oblique view?
In cabinet oblique drawing, we take a front face of an object, and draw the sides, or depths, in 45 degrees. It is very important to keep in mind, that we reduce the depth by half, so every dimension at 45 degrees is divided by two. We apply this correction so that the shape or furniture does not look too long or deep.
Do you dimension oblique drawings?
Dimensioning of Oblique Drawing. Dimensioning of the oblique drawing is similar to that of isometric drawing. Mostly, dimensioning is done along the receding axis. The angle of writing is also according to this axis. In addition to this, to write more dimensions, sides can be used.
