Table of Contents
The toilet flange needs to be on top of the finished floor. Meaning the bottom edge of the flange needs to be on the same plane as the toilet. So if your toilet sits on the tile, the flange needs to be on top of the tile too.
Is toilet flange supposed to be level with floor?
With the toilet removed, you can see the toilet flange and measure its height above the floor. The optimum flange height to aim for is 1/4 inch above the finished floor. This typically allows for almost any type of wax ring to be used and still ensure a good seal.
Can toilet flange be lower than floor?
In a typical toilet installation, the floor flange that sits inside the drain opening below the toilet should be positioned so that its bottom surface rests flush against the finished floor or no more than 1/4 inch above or below the floor.
Can a toilet flange be flush with floor?
Setting a closet flange flush with the floor The other option for installing a toilet flange is to set it flush with the floor. The process for setting it this way is similar to the above-the-floor method in almost every way including the requirement for a wax ring and closet bolts.
Should toilet sit flush with floor?
The flange should sit flush on top of the finished floor.
What if toilet flange is not level?
If the toilet flange is not level, you should replace it. First, empty the toilet, remove the toilet tank and bowl, then remove the existing flange. Next, install the new flange and place a wax ring around it to keep it level.
What do you do if the toilet flange is above the floor?
To use grout to fix your flange: Start by mixing your grout. Get your toilet in place and set your toilet on four rubber shims. Take your mixed grout and pack it into the gap. Wait 24-hours before the grout to dry. Once dried, remove the shims.
How do you install a toilet when the flange is too low?
Installation process is simple: install the gasket on top of the toilet flange on the floor, add spacer rings to match the new floor surface level, add the extender, add a standard wax ring the set the toilet on top. I like the product but I see some potential issues: Set-Rite spacer rings are hollow.
How far can a toilet flange be above the floor?
The optimum toilet flange height is approximately ¼ inch above the floor to achieve the best seal and overall fit.
How much does a plumber charge to change a flange?
On the other hand, hiring a plumber to replace the flange will ensure that the job is done right by a licensed, experienced professional. The cost for a plumber to replace the toilet flange varies by region and service provider, but the average price range is approximately $130 to $310.
Does tile go under toilet flange?
Does tile go under the toilet flange? Yes, the toilet flange should be seated over the tile so that it can be secured tightly through the bolts.
Do you tile around a toilet or under it?
To install tile properly around the toilet, you need to affix it to the floor under the fixture. Because toilets sit on top of tile, any rough cuts are hidden, making it easy to achieve the appearance of tile that has been custom-cut for your bathroom.
Does toilet flange go inside or outside pipe?
This toilet flange is designed to glue on the inside of the pipe or expand inside the pipe. Leave the old toilet flange right in place and glue on the new one at the right elevation for the floor, if it’s plastic. The flange should be sitting with the bottom edge flush with the top of the floor.
Can you shim up a toilet flange?
How to Level a Toilet Using Toilet Shims. Toilet shims are thin plastic or rubber tabs that are used to level a toilet. You can also use homemade wooden shims or stainless steel coins. If a toilet is installed on an uneven floor or if the toilet flange is too high off the floor, the toilet will need to be shimmed.
Why is toilet crooked?
Usually, the hole in the toilet is big enough to rotate it at least a few degrees, and if they used the slots, probably more as the bolt can move, too. Also, it’s a good idea to use a second nut and washer to lock the bolt into the flange, and if they did that, it won’t move without removing the toilet.
Are there different size toilet flanges?
Toilet flanges come in six different types and three standard sizes with the option of an odd fit. The types are based on the material from which they are made, that is aluminum, copper, brass, stainless steel, plastic, and cast iron. The sizes also range from a four by three, four-inch, or three inches flange.
Can you use 2 wax rings when installing a toilet?
You can certainly install a toilet with multiple wax rings, in fact sometimes it is necessary to make sure you don’t have a leak. You can buy an extra-thick wax ring, or you can just buy two rings and stack one on top of the other.
Is there something better than a wax ring?
Why Better Than Wax? This innovative wax-free toilet seal fits any drain, any toilet, can be repositioned during installation, and excessive plunging won’t cause leaks. Better Than Wax includes a stackable wax-free seal, slide-on spacer, and no rust brass bolts and hardware.
How far should a toilet flange be away from the wall?
Standard drywall is 1/2 inch thick, so the plumber should set the toilet flange at least 15-1/2 inches from the center of the flange to the wall framing. The standard distance from the back wall is 12 inches, or 12-1/2 inches from the center of the flange to the wall framing.
Can toilet flange go above floor 1 2?
The height to aim for is 1/2 inch above the floor. This allows almost any type of wax ring to be used, and still ensure a good seal.
Why do toilet wax rings fail?
One very common cause of wax ring problems is loose toilets. If the toilet is not firmly mounted, or gets loose to the point where it rocks a bit, it can cause the wax ring to lose its seal. When installed, a wax ring is compressed to fit the flange and the toilet, creating the seal.
Can you use thinset to level a plywood floor?
Well, the answer is actually no. Mortars cannot be used to level or patch a floor – ever! The most versatile self-leveler is Novoplan 2 Plus, a high-strength, cement-based underlayment and repair mix for use over interior concrete, plywood and other approved floor surfaces.
How much should a plumber charge to replace a toilet?
A plumber charges around $375 to replace a toilet. Most charge between $275 and $480. This includes the cost of removing and disposing of your old toilet. Note that the actual cost to replace a toilet depends on your location, the type of toilet and the difficulty of the installation.
