Table of Contents
Fiberglass Batt Insulation Characteristics Thickness (inches) R-Value Cost (cents/sq. ft.) 3 1/2 11 12-16 3 5/8 13 15-20 3 1/2 (high density) 15 34-40 6 to 6 1/4 19 27-34.
What is the R-value of 3 and 1/2 in of fiberglass?
with an R-value of 3.5 per inch per inch of thickness.
What is the R-value of 3.5 inch fiberglass insulation?
The thicker the insulation, the higher its thermal resistance, or R-value. Standard 3.5-inch thick fiberglass insulation has an R-value of 11, and fits neatly in two-by-four wall stud spaces.
What is the R-value of 3 1/2 inch insulation?
For example, standard low-density batts, at their nominal rated thickness — R-11 at 3 1/2 inches, or R-19 at 6 inches — have an R-value of about 3.1 per inch.
What is the R-value of fiberglass insulation?
Blown-in fiberglass has an R-value of 2.2 to 2.7 per inch. Batts. Fiberglass batts and rolls are ideal for placement between framing during construction in floors, walls, attics, and ceilings. They’re denser than blown-in insulation, offering an R-value of up to 4.3 per inch.
Can you put R30 insulation in 2×4 walls?
R-30 fiberglass insulation is designed to be in a roof or ceiling cavity framed with 2x10s. It is way too thick for 2×4 walls.
Can you put R19 insulation in a 2×4 wall?
Use R-19 or R-21 kraft-faced fiberglass insulation for two-by-six (2×6) walls. This combination ensures that the insulation is neither too loose nor too tightly packed within the walls. Two-by-four (2×4) stud walls with true 4-inch depth.
How many inches of insulation is R30?
Fiberglass Chart R-Value Thickness Bags / 1000 Sq Ft R49 16.25” 22.6 R44 14.75” 20.1 R38 12.75” 16.8 R30 10.25” 13.0.
Is a higher R-Value better for insulation?
An insulating material’s resistance to conductive heat flow is measured or rated in terms of its thermal resistance or R-value — the higher the R-value, the greater the insulating effectiveness.
What insulation is best for exterior walls?
What Insulation is Best for Exterior Walls? Fiberglass batt insulation is affordable and effective. Loose-fill cellulose insulation is more commonly known as blown-in insulation. Spray foam insulation is another popular exterior insulation option.
What is the thinnest insulation with the highest R-value?
Thermablok® Aerogel is a revolutionary advancement in thermal technology offering the thinnest insulation available to prevent thermal and cold bridging. Classed as a Super Insulation, Aerogel has the highest insulation value of any known material with the lowest thermal conductivity value of any solid (0.015W/mK).
What insulation has the highest R-value?
Vacuum insulated panels have the highest R-value, approximately R-45 (in U.S. units) per inch; aerogel has the next highest R-value (about R-10 to R-30 per inch), followed by polyurethane (PUR) and phenolic foam insulations with R-7 per inch.
What R-value is needed for ceiling insulation?
Depending on where you live and the part of your home you’re insulating (walls, crawlspace, attic, etc.), you’ll need a different R-Value. Typical recommendations for exterior walls are R-13 to R-23, while R-30, R-38 and R-49 are common for ceilings and attic spaces.
Does doubling insulation Double R value?
Doubling the thickness of insulation will double the insulation’s R-value, cutting heat loss in half. Each time the insulation layer is doubled in thickness, this rule applies.
How many inches of insulation do I need in the attic?
The recommended level for most attics is to insulate to R-38 or about 10 to 14 inches, depending on insulation type.
Does fiberglass insulation degrade over time?
Unless damaged, it can last 80 to 100 years in most houses before it needs to be replaced. However, insulation can start falling from fiberglass batts after 15 to 20 years, so if your insulation was installed in batts well over a decade ago, it might be time for an inspection or a home energy audit.
What R-value can you get in a 2×4 wall?
They are available in widths suited to standard spacings of wall studs and attic or floor joists: 2×4 walls can hold R-13 or R-15 batts; 2×6 walls can have R-19 or R-21 products. Loose-fill insulation—usually made of fiberglass, rock wool, or cellulose—comes in shreds, granules, or nodules.
What is the best way to insulate a 2×4 wall?
One option is to use polyurethane rigid foam insulation; it is available with R-values ranging from R-18 to R-28 at a 3½-inch thickness. Polyurethane rigid foam is a closed-cell insulation, which means the cells in the insulation are densely packed and filled with a gas.
How much insulation can I put in a 2×4 wall?
A 2×4 wall cavity can be insulated from R-13 to roughly R-25. A 2×6 wall can be insulated from R-19 to R-39. Material selection, density, and cavity depth all play a role in the “cavity” R-value of a wall.
Can you use R19 insulation in ceiling?
Most homes only have R19 in attics. To give you an idea that’s only 5 1/2 inches of insulation. That’s ok for your walls. So by adding another R19 “5 1/2 inches will give you an R38 value.
Can you have too much insulation?
It is possible to over-insulate your house so much that it can’t breathe. The whole point of home insulation is to tightly seal your home’s interior. But if it becomes too tightly sealed with too many layers of insulation, moisture can get trapped inside those layers. That’s when mold starts to grow.
What type of insulation is best for ceilings?
INSULATION TYPE: Foam Board or Rigid Foam Panels Foam boards work well to insulate everything from foundation walls and basement walls to unfinished floors and ceilings.
Which is better R19 or R30 insulation?
Insulation in your walls and ceilings slows down this heat transfer. The bigger the R value, the better the insulation is at slowing down the heat transfer. So R19 is better insulation than R13, and R30 is better than R19. The larger the R value, the better the insulation value.
How thick is R60 insulation?
The average recommended level is 17 inches of R60.
What is the R value of 10 inches of blown insulation?
R-value of Materials and Depths Material R-value/in 10″ Mineral Wool blown (wall) 3.1 – 4.0 31.0 – 40.0 Cellulose blown (attic) 3.2 – 3.7 32.0 – 37.0 Cellulose blown (wall) 3.8 – 3.9 38.0 – 39.0.
