Table of Contents
You’ll have to practice to develop a feel for it. For a really smooth finish, repeat the troweling step two or three times, letting the concrete harden a bit between each pass. At first, hold the trowel almost flat, elevating the leading edge just enough to avoid gouging the surface.
How long do you wait to float concrete?
Allow all of the water to disappear before you do anything else. This can take 20 minutes or 4 hours depending on the temperature, humidity and how hard the wind is blowing. After the bleed water is all gone, you can get out your steel finishing trowel and put on the final touches.
How many times do you bull float concrete?
Frequently two passes with the screed is necessary to achieve desired grade. If you are going to be pouring a large slab with a width of 15′ feet or greater it becomes difficult to strike off this much concrete. Even at fifteen feet you will need three people working the screed.
Do you need to float concrete?
Floating has to be done on virtually every concrete job after concrete is poured and leveled. When done properly, floating pushes the aggregate down into the concrete and encourages moisture to rise, helping the concrete dry and creating a smoother surface.
What to do if it rains after pouring concrete?
Tips for Handling Rain After Pouring Concrete Don’t broadcast dry cement onto the concrete to soak up surface water. This will impair the finish and further weaken the top layer. Instead, once the rain passes, use a float to push the water off the edge of the slab before you start finishing.
How long should concrete cure before putting weight on it?
Initial Setting Times for Concrete In standard industrial cases, full strength concrete is recognized at 28 days. At seven days, you should have concrete that is cured to 70% full strength or greater. But to answer the question of, “How long does concrete take to set?” concrete setting time is generally 24 to 48 hours.
Can you over float concrete?
If you can’t reach the entire slab from the edges with a darby, rent a bull float and handle to use instead. Two passes over the surface with the darby are enough. Overworking the concrete will draw too much cement and fine sand to the top and create a weak surface.
Can you finish concrete with a bull float?
A bull float is used to level and smooth freshly poured concrete. Concrete used for visible projects, such as driveways, patios and sidewalks, often requires finishing. A bull float is a tool used for finishing concrete.
How do you know when to bull float concrete?
Concrete Bull Floats and Darbies Darbying or bull floating should be done immediately after “screeding”, or after the concrete has been tamped if tamping was done. This process should be finished before excess moisture or bleedwater appear on the surface.
What’s the difference between a float and a trowel?
A float has a thicker base than a trowel and is usually made of plastic, sponge, rubber, wood or magnesium – a lightweight pale grey metal. It’s used to even up the surface on plaster or concrete, make it firmer and give whatever texture is required. The finish will depend on the float chosen.
Can you over work concrete?
Never overwork or over finish the surface of any exposed concrete slab. This brings too much fine material to the surface, works out the designed air entrainment*, and will weaken the surface of the slab leaving the top of slab more vulnerable to freeze/thaw damage and sheet scaling*.
What is the purpose of floating concrete?
A concrete float is a tool used to finish a concrete surface by making it smooth. A float is used after the surface has been made level using a screed. In addition to removing surface imperfections, floating will compact the concrete as preparation for further steps.
How do you make concrete shiny?
After you stain your concrete floor with the color of your choice, you should apply a concrete sealer. A glossy sealer creates a shiny surface, and an acrylic wax adds an additional protective coat.
Whats the difference between cement and concrete?
What is the difference between cement and concrete? Although the terms cement and concrete often are used interchangeably, cement is actually an ingredient of concrete. Concrete is a mixture of aggregates and paste. The aggregates are sand and gravel or crushed stone; the paste is water and portland cement.
How long does 4 inches of concrete take to cure?
Concrete typically takes 24 to 48 hours to dry enough for you to walk or drive on it. However, concrete drying is a continuous and fluid event, and usually reaches its full effective strength after about 28 days.
Can I pour concrete in a hole full of water?
The good news is that you can pour the concrete in water. The biggest issue with pouring concrete under water is movement. If the water is moving, it can wash away the cement paste that’s holding the sand and gravel together. But if the water is calm, then it’s not a problem at all.
Can I drive on concrete after 3 days?
Your new concrete is designed to reach 90% of its full strength potential after 7 days, so feel free to drive your personal vehicle on it then. It will take additional time before you can drive or park heavy equipment or machinery on your newly poured concrete, so make sure to wait at least 30 days.
How strong is concrete after 3 days?
From above table, we see that, concrete gains 16 percent strength in one day, 40 percent in 3 days, 65% in 7 days, 90% in 14 days and 99% strength in 28 days. Thus, it is clear that concrete gains its strength rapidly in the initial days after casting, i.e. 90% in only 14 days.
When should I start watering my concrete?
To put it simply, the goal is to keep the concrete saturated during the first 28 days. The first 7 days after installation you should spray the slab with water 5-10 times per day, or as often as possible. Once the concrete is poured the curing process begins immediately.
Does concrete take 100 years to cure?
Does concrete take 100 years to cure? No, this is a bit of a myth with the concrete industry. While concrete does continue to harden indefinitely, pore moisture has to drop below a certain level at some point and this isn’t typically 100 years.
What happens if you finish concrete too soon?
More often, premature finishing or improper first (bull floating) or second floating results in trapping rising bleed water and air below the top surface of the concrete (Image 2). When this occurs, the resulting weak or soft zone below the surface causes the top surface of the concrete to flake or scale off.
Why does magnesium float on concrete?
Magnesium smooths the surface of fresh concrete and opens the pores for proper evaporation, all without pulling the surface like a wood or resin tool. Most magnesium floats are extruded or cast.
What happens if you dont finish concrete?
When you don’t finish concrete floors, many things can occur such as wear and tear in high traffic areas, unwanted and unsightly cracks, higher associated costs, increased cleaning and maintenance, and water retention.
How long do you wait to float concrete?
Allow all of the water to disappear before you do anything else. This can take 20 minutes or 4 hours depending on the temperature, humidity and how hard the wind is blowing. After the bleed water is all gone, you can get out your steel finishing trowel and put on the final touches.
How many times do you bull float concrete?
Frequently two passes with the screed is necessary to achieve desired grade. If you are going to be pouring a large slab with a width of 15′ feet or greater it becomes difficult to strike off this much concrete. Even at fifteen feet you will need three people working the screed.
When should you bull float concrete?
Concrete Bull Floats and Darbies. Darbying or bull floating should be done immediately after “screeding”, or after the concrete has been tamped if tamping was done. This process should be finished before excess moisture or bleedwater appear on the surface.
Do you need to float concrete?
Floating has to be done on virtually every concrete job after concrete is poured and leveled. When done properly, floating pushes the aggregate down into the concrete and encourages moisture to rise, helping the concrete dry and creating a smoother surface.
What to do if it rains after pouring concrete?
Tips for Handling Rain After Pouring Concrete Don’t broadcast dry cement onto the concrete to soak up surface water. This will impair the finish and further weaken the top layer. Instead, once the rain passes, use a float to push the water off the edge of the slab before you start finishing.
How long should concrete cure before putting weight on it?
Initial Setting Times for Concrete In standard industrial cases, full strength concrete is recognized at 28 days. At seven days, you should have concrete that is cured to 70% full strength or greater. But to answer the question of, “How long does concrete take to set?” concrete setting time is generally 24 to 48 hours.
Can you over float concrete?
If you can’t reach the entire slab from the edges with a darby, rent a bull float and handle to use instead. Two passes over the surface with the darby are enough. Overworking the concrete will draw too much cement and fine sand to the top and create a weak surface.
Why does magnesium float on concrete?
Magnesium smooths the surface of fresh concrete and opens the pores for proper evaporation, all without pulling the surface like a wood or resin tool. Most magnesium floats are extruded or cast.
Do you have to use a bull float on concrete?
A bull float is used to level and smooth freshly poured concrete. Concrete used for visible projects, such as driveways, patios and sidewalks, often requires finishing.
What is the difference between a float and a trowel?
A float has a thicker base than a trowel and is usually made of plastic, sponge, rubber, wood or magnesium – a lightweight pale grey metal. It’s used to even up the surface on plaster or concrete, make it firmer and give whatever texture is required. The finish will depend on the float chosen.
What is the purpose of floating concrete?
A concrete float is a tool used to finish a concrete surface by making it smooth. A float is used after the surface has been made level using a screed. In addition to removing surface imperfections, floating will compact the concrete as preparation for further steps.
Can you over work concrete?
Never overwork or over finish the surface of any exposed concrete slab. This brings too much fine material to the surface, works out the designed air entrainment*, and will weaken the surface of the slab leaving the top of slab more vulnerable to freeze/thaw damage and sheet scaling*.
Can you smooth concrete after it dries?
Sand the Surface and Wash the Concrete Finish by fine-tuning with light sandpaper, until the surface is perfectly smooth. We recommend using a hand planer to smooth and compact the surface. If the concrete dries a lot then we recommend that you add water to the surface, this will help you give it a good finish.
How long does 4 inches of concrete take to cure?
Concrete typically takes 24 to 48 hours to dry enough for you to walk or drive on it. However, concrete drying is a continuous and fluid event, and usually reaches its full effective strength after about 28 days.
Can I pour concrete in a hole full of water?
The good news is that you can pour the concrete in water. The biggest issue with pouring concrete under water is movement. If the water is moving, it can wash away the cement paste that’s holding the sand and gravel together. But if the water is calm, then it’s not a problem at all.
Can I drive on concrete after 3 days?
Your new concrete is designed to reach 90% of its full strength potential after 7 days, so feel free to drive your personal vehicle on it then. It will take additional time before you can drive or park heavy equipment or machinery on your newly poured concrete, so make sure to wait at least 30 days.
How strong is concrete after 3 days?
From above table, we see that, concrete gains 16 percent strength in one day, 40 percent in 3 days, 65% in 7 days, 90% in 14 days and 99% strength in 28 days. Thus, it is clear that concrete gains its strength rapidly in the initial days after casting, i.e. 90% in only 14 days.
When should I start watering my concrete?
To put it simply, the goal is to keep the concrete saturated during the first 28 days. The first 7 days after installation you should spray the slab with water 5-10 times per day, or as often as possible. Once the concrete is poured the curing process begins immediately.
Does concrete take 100 years to cure?
Does concrete take 100 years to cure? No, this is a bit of a myth with the concrete industry. While concrete does continue to harden indefinitely, pore moisture has to drop below a certain level at some point and this isn’t typically 100 years.
