Table of Contents
Well Drilling Cost Drilling a well costs $5,500 for an average depth of 150 feet. Most projects range between $1,500 and $12,000. Expect to pay between $15 and $30 per foot of depth, or up to $50 for difficult terrain. For shallow depths, digging may be a more affordable solution as $10 to $25 per foot.
How much does it cost to put a well on a property?
Drilling a well costs $5,325 to $9,180 for an average depth of 150 feet. Most homeowners spend $3,750 to $15,300, or $25 to $65 per foot for well installation. Digging a shallow well costs $1,800 and $3,000.Well Drilling Cost. National Average Cost $9,180 Maximum Cost $30,000 Average Range $3,750 to $15,300.
Is digging a well worth it?
Low-yield wells can produce enough for daily personal water use, but you might not have enough for watering your yard or filling a pool. Even if the well can’t provide all of your water needs, it might be worth digging if you can offset some of your water usage from your city’s supply.
Is it possible to dig your own well?
Drilling a well by hand is a lot of work, but it can be done with the right equipment. Whether you’re looking to drill a shallow or deep well, this skill is perfect for those seeking self-reliance. Wells are normally drilled on private land where city or rural water isn’t available.
How deep should a well be for drinking water?
The quality of your water depends on several factors including geology and water levels. In order to allow for maximum ground filtration to remove impurities, your well depth should be at least 100 feet. As a general rule, the deeper you drill, it’s more likely that there will be minerals present.
How deep is the average well?
Most household water wells range from 100 to 800 feet deep, but a few are over 1,000 feet deep. Well yields can be increased by fracturing the bedrock immediately around the drill hole and intercepted rock faults.
How long do wells last?
The average lifespan for a well is 30–50 years. 2. How deep is the well? Drilled wells typically go down 100 feet or more.
Is it OK to drink well water?
Can you drink well water? The answer is most likely yes, but testing and treatment are crucial. As long as you closely monitor the condition of your water supply and take appropriate measures to ensure its quality, well water can be safe to drink.
Do wells run out of water?
When a well “runs dry” it doesn’t mean that the well will never produce water again. Aquifers can recharge through a combination of more precipitation and less pumps pulling water out of that aquifer. Sometimes wells can run dry permanently, but that is quite uncommon.
Can you dig a well next to a river?
Successful wells are often drilled near rivers; groundwater may be available even if the river is temporarily dry (Figure 2). Reliable wells have even been located near broad sandy riverbeds which are active once every 5-10 years (Dijon, 1981).
How Far Should a well be from a house?
Any contamination in your neighbor’s well can travel into your well. Some activities legally require more than a 50-foot zone of protection. As a general guidance, personal drinking water wells should have a minimum horizontal distance of at least 10 feet and preferably 25 feet from such boundaries.
Can you build a well anywhere?
The simple answer to Connie’s question is yes. You probably can drill your own well on your property. You, of course, would have to contact your local building department to see if there are any regulations that must be followed.
How do I find the water table in my area?
How to Find My Water Table Call your local County Extension Office. It may have statistics for the average annual water table level in your area. Look online. Check out the website for your local Water Resources Office. Dig. This is the most reliable way to find the water table level on your land.
Are deeper wells better?
In general, when it comes to water quality and well depth, there’s one golden rule: the deeper the well, the better the water quality. As you go deeper down, there’s a higher chance that the water you encounter will be rich in minerals.
How often should you disinfect your well?
Homeowners with private wells should have their well water tested every 3 to 5 years for some contaminants, including bacteria. If these tests turn up positive for bacteria, chlorinating the well may be a way to resolve the problem.
What is too deep for a well?
On average, to be deep enough to reach the bedrock, a water well would need to be anywhere from 100 to 500 feet deep, though there are some places where the well needs to be up to 1000 feet deep.
How fast do wells refill?
In ideal conditions, a water well will refill at five gallons per minute. It takes two hours to fill a 600-gallon well. Not all wells exist under ideal conditions. There are several factors that can speed up or delay the time it takes to refill.
Is 10 gallons per minute a good well?
Typical numbers for well recovery rates (if measured honestly over a 24-hour period) run from a fraction of a gallon per minute (a terribly poor well recovery or flow rate) to 3 gallons a minute of water flow (not great but usable) to 5 gallons per minute (just fine for residential use) to more than 10 gpm (a great.
