Table of Contents
What can you do with a thickness planer?
A thickness planer serves three unique purposes that other tools do not: 1) It makes the second face of a board parallel to the other face; 2) It smooths rough stock; and 3) It reduces stock down to the exact thickness you need.
What is the main purpose of a planer?
A wood planer helps you even out a piece of wood into a board with the exact same thickness everywhere. A correctly planed board is completely flat on both sides, eliminating rough spots or leftover bark.
What is the difference between a planer and a thicknesser?
“A planer is a thicknesser. That smooth side goes down onto the bed, and the thicknesser (planer) cuts slices off the top (unsmoothed) side. In other words, you put a board into the planer to make it thinner after you have already established one flat side using the jointer (or a hand plane.).
Can you run pressure treated wood through a planer?
There should be no issue running pressure-treated boards through a planer, however, if you do a little housekeeping afterward. Give the planer a good blasting off with an air hose after you finish for the day to reduce the amount of PT sawdust left in the machine.
Which type of stock should never be run through the planer?
What should you avoid when using a jointer or planer? Do not cut stock that has loose knots, splits, defects or foreign objects (e.g., metal stone) in it. Do not leave the machine running unattended. Shut off the power and make sure that the cutting head has stopped revolving before leaving the area.
What is the purpose of roles in thickness planer?
The cutting tool of a thickness planer is a series of knives on a revolving shaft. Single planers have one revolving shaft, which planes (finishes) the top surface of the board; the shaft is fixed above the table, and the board is moved along the table by the feed rolls.
Does a planer sand wood?
Whereas sanders are used to alter the finish of wood, a wood planer is used to even out wood to an exact thickness. With a planer you can smooth rough lumber, clean up sawn edges and give new life to old wood. Each planed piece of wood can be used by itself or glued to other planed pieces for a thicker board or block.
Does Ryobi make a thickness planer?
Ryobi 12.5″ Thickness Planer (Model AP1305) They are also an essential tool for any woodworker looking to take on finish work projects like furniture or cabinetry building. Recently we got the chance to check out and test out the new Ryobi 12.5″ thickness planer (model AP1305).
Can you use a planer as a thicknesser?
A question we are often asked, particularly at woodworking shows and demonstrations, is why we need to use a planer as well as a thicknesser to achieve the above. These machines have a great deal of appeal to those relatively new to woodworking as they are less costly than a planer thicknesser and can be bench mounted.
Can a planer be used as a jointer?
A planer can be used as a jointer by following a few woodworking tricks. If your workshop doesn’t have a jointer to square up an edge or your wood piece is too large to fit through, you can use your planer to flatten both pieces of wood.
Why is a jointer called a jointer?
The jointer derives its name from its primary function of producing flat edges on boards prior to joining them edge-to-edge to produce wider boards. The use of this term probably arises from the name of a type of hand plane, the jointer plane, which is also used primarily for this purpose.
Can I use a planer on painted wood?
Yes, the paint dulled the blades; no, it didn’t ruin them. I just had to sharpen them when I was done. Painted wood dulls planer blades rapidly because paint contains abrasive minerals. If you are really attached to certain pieces of painted lumber, a set of dull blades may not be a huge issue.
Can you run wet wood through a planer?
Tool Wear. Trying to put “wet” lumber through a planer, a jointer, a sander or even cutting it with a saw can cause both damages to the tools and danger to you.
Can you run stained wood through a planer?
A: You could plane off an old finish, but it’s not worth the risk. Planer cutterheads can generate sufficient friction to soften such finishes as polyurethane, gumming up their knives. After sanding away the finish, feed the wood through a planer to erase the sanding marks.
How much wood should the thickness planer remove in one pass?
Examine the width of the lumber. Most planers remove a maximum of 3 mm per pass. If a narrow piece of lumber is being planed, the maximum amount may be removed. A piece that it at the maximum width of the planer may cause the motor to overheat and the cutter to stall.
How short of a piece of wood can you run through the planer?
Most planer manufacturers advise against planing pieces shorter than 12″.
Can you plane wood across grain?
Depending on how much material you need to take off, you could run it through a drum sander, or do the hand tool route and you a hand plane. Either way, you do not want to send parts through a planer cross grain. It is unsafe, bad for the tool, and will not produce a satisfying product in most cases.
