Table of Contents
Building High-Tensile Fence Dig holes for the corner posts. Set corner posts. Build braces. Attach insulator tubes to corner post. Unroll the wire. Lay out line posts. Attach the insulator tubes and wire on the second corner, before you walk (or drive) back to the first corner. Cut and attach wire on the first corner.
How tight should a high tensile fence be?
– Over-tensioning hi-tensile wire: Hi-tensile wire needs only between 150 to 200 pounds of tension. If you are used to putting up barbed wire, then you would normally put about 300 to 350 pounds of tension on it. So, don’t over tension hi-tensile wire. This is normally the last step in putting up your fence.
How far apart should h braces be?
Double H Brace Pull Assemblies: Double H Brace pull assemblies are required in straight fence spans at a maximum spacing of 660 feet. Brace wire shall be high tensile, galvanized steel, or 9 gauge soft wire. Adjoining Fences: A fence adjoining an existing fence must terminate in a brace assembly as required above.
How far apart are high tensile fence posts?
As a rule of thumb, line posts are spaced about 30-feet apart but it depends on many factors including the number of wires in the fence, the terrain, as well as type and number of animals being controlled. Increasing the distance between posts reduces the cost of the fence.
What gauge is high tensile wire?
This wire is a barbless (smooth), single strand fence wire produced from a high tensile steel. The standard size is 12½ gauge with a minimum breaking strength of 1,350 pounds.
Does high tensile wire rust?
In recent years all of my new fence construction is with hi-tensile steel wire. Class 3 galvanized coating resists rust up to 3-times longer than traditional farm store wire.
How do you build a high tensile fence for cattle?
Building High-Tensile Fence Dig holes for the corner posts. Set corner posts. Build braces. Attach insulator tubes to corner post. Unroll the wire. Lay out line posts. Attach the insulator tubes and wire on the second corner, before you walk (or drive) back to the first corner. Cut and attach wire on the first corner.
How high should fence be for cattle?
Fence height should be at least 48 inches high to prevent animals from climbing over the fence. Woven wire fence can be used with cattle provided there are several strands of barbed top wires used to prevent the cattle from rubbing the woven wire down.
What type of fencing is best for cattle?
Three basic fence types are best suited for cattle: traditional barbed wire, woven wire and high tensile smooth wire, says Ken Edwards, a longtime cattle owner and technical support manager with Red Brand-Keystone Steel & Wire.
How far apart should fence posts be for woven wire?
Installing the Fence: Basics Spacing: Anchor posts should be at the corners or ends of the fence, and every 30- 50 feet throughout the length of it. T-posts should be every 10 feet.
Does welded wire fence need to be stretched?
But Not Too Tight It is important to have a level pull uniformly across the height of the fence to avoid distorting the mesh. The amount of tension is determined by the type of mesh. Welded wire fencing material cannot be tightened as much as woven wire meshes, such as field fence, horse fence, deer and wildlife fence.
How many fence posts do I need for 1 acre?
If we assume that your property is equal on 4 sides, then it is as simple as taking the square root of 43,560 square feet. This gives you 209 feet on each side, which would require 835 linear feet of fence to enclose the entire acre property (209 feet times four sides is equal to 835 linear feet).
How many bags of cement do I need for a fence post?
1 – 4 bags of concrete per fence post are typically what’s needed. This depends on the type of soil, fence design, height, post size and bag weight. In general the depth of the post’s hole needs to be 1/3 to 1/2 of the above ground height of the post.
How far apart should T posts be for cattle?
Fence posts need to spaced 50-100 feet apart. Using the right energizer.
Will high tensile fence keep goats in?
Fencing is the most critical factor in raising goats on pasture. Goats can be controlled with four to five strands of high-tensile electrified wire. The wire spacings can vary from 6 to 8 inches near the ground to 8 to 12 inches for the top strands.
How many acres will 1000 feet of wire cover?
To Cover This Size Area You Need This Amount of Wire 1/2 Acre 600 Feet 1 Acre 1000 Feet 2 Acres 1300 Feet 3 Acres 1500 Feet.
How strong is high tensile wire?
High tensile wire equates to a high carbon content, and will not stretch as much as low carbon wires. Typically used exclusively in barbed wire, 15 gauge high tensile wire is only going to stretch 1.5-2%, and will break at about 550 lbs., making barbed wire break at 1,100 lbs.
Which is stronger 14 gauge or 16 gauge?
16ga steel is . 065” inches thick, that is about 1/16th of an inch thick. 14 gauge in comparison is . 083 inches thick which doesn’t sound like much except it is almost 30% thicker (27.6% to be exact).
How far apart should electric fence insulators be?
Electric Fence Post Installation Fencing parameters Spacing (feet) Electric 12-20 High-tensile, level terrain 30-90 High-tensile, difficult animals, rolling terrain 15-20 Poly tape and poly wire 12.
