Table of Contents
Follow these steps: Turn the handwheel on the CO2 regulator to the left to open the air tank. Flip the shut-off valve on the regulator to ON. You should hear air enter the gas lines. Adjust the PSI so the pressure gauge reads between 10 and 15. Carefully place the CO2 tank into the cabinet and close the door.
What should CO2 be set at for kegerator?
What pressure should my CO2 tank be set to? This will depend on the beer you are serving but most American breweries recommend a pressure between 10-14 PSI.
Do you leave the CO2 on in a kegerator?
To be on the safe side, we always recommend shutting off the CO2 when you do not have a keg hooked up. However, just in case a gasket or o ring does not make a tight seal, shutting the CO2 off will prevent you from losing your CO2 while you do not have a keg hooked up.
How long does a 5lb CO2 tank last in a kegerator?
A 5-lb CO2 tank will last between 6-8 half barrel, or full kegs, before it will need to be filled. A 10-lb CO2 tank will dispense between 10-13 full kegs per fill. This number can be higher or lower based on how often you’re using your kegerator, the level of carbonation, and if your system is properly balanced.
Do you turn on CO2 before tapping keg?
You want to make sure that the regulator is pressurized before tapping the keg to prevent your beer from flowing back into the air lines when you tap it. Take the dust cover off of your keg and connect the keg coupler.
What PSI should a kegerator be?
We recommend setting the regulator at 12 PSI. NOTE: On regulators designed for draft beer, turning clockwise will increase the output pressure, and turning counter-clockwise will decrease the output pressure. Under normal circumstances we recommend setting the regulator at 12 PSI.
Do you leave gas on kegerator?
If you have no leaks and your beer is carbed you can disconnect it and it will,( and it should ) have no loss off pressure. If you leave it connected you will not waste any c02 at all. Once you have the proper pressure, and no leaks, your good to go.
How often do you need to clean kegerator lines?
At a minimum you should clean your tap lines once every six weeks. Our recommendation is to clean and sanitize your tap lines between each keg you serve on your draft system to make life easier.
Can you use any CO2 for beer?
Food grade CO2 can be used to dispense beer, keeping it from going bad as fast as it does with hand pumps (Atmospheric Air). So some of your keg-beer shops will have it. All Pop Distributors will have it too since its required for both BiB and premix systems, but they tend to cost more for the same CO2.
Does Walmart fill up Co2 tanks?
Unfortunately, Walmart does not fill Co2 tanks as of 2022. Customers can purchase Co2 fill stations at Walmart for at-home use or buy their small, pre-filled, 12- to 90-gram Co2 cartridges. Customers can also visit other businesses such as sporting goods stores or welding supply stores to refill Co2 tanks.
Does Lowes fill Co2 tanks?
Lowe’s does not fill or sell CO2 tanks. However, there are plenty of other stores that do such as DICK’s Sporting Goods and Airgas. Check your nearest equipment supplies store, or you can even fill your CO2 tanks from home after ordering them online.
Can you lay a kegerator on its side?
Unpackage the Kegerator If the unit has been transported on its side, let the unit stand upright for at least 24 hours before plugging it in. Move the unit to its final location and install it on a level surface. Make sure to provide clearance around the unit for ventilation, per the manufacturer’s instructions.
How long should I let a keg settle before tapping?
Do not agitate the keg. If there has been excessive agitation during transportation, allow the keg to settle for 1 to 2 hours before tapping. Make sure the beer faucet is in the off position prior to tapping. Remove the dust cover from the beer keg.
How do you fix a foamy kegerator?
How To Stop A Kegerator Creating Foamy Beer Step 1: Check the temperature of your beer. Step 2: Clean or replace your beer lines. Step 3: Check the beer line is correctly installed. Step 4: Check the CO2 regulator. Step 5: Check that you are pouring your beer properly. Step 6: Is the keg ready to pour?.
Why is there so much foam in my kegerator?
The most common causes are: Incorrect Temperature – If the beer is too warm or too cold, it will be more easily disturbed and pour as foam. Make sure the glass is near the bottom of the keg (but not touching it) since that is where the beer is coming from.
How do I know when my co2 tank is empty?
How do I know if my gas cylinder is empty? Make sure the carbonating cylinder is tight enough and retighten it if necessary by twisting the cylinder to the right. If you’re still not getting bubbles and if you don’t hear a sputtering sound when you press the carbonating button*, you may be out of gas.
How many 12oz beers are in a keg?
Keg Sizing Information 1/2 barrel = 15.5 gallons = 124 pints = 165 12oz bottles – (Full Size Keg) 1/4 barrel = 7.75 gallons = 62 pints = 83 12oz bottles (Pony Keg).
