Table of Contents
Turn the kingpin nut anti-clockwise to loosen the trucks but do so in small increments and test as you go so as not to loosen the trucks too much. To tighten your trucks, turn the nut clockwise.
How do I make my trucks tighter?
Lean to turn in a direction (frontside or backside), and gradually press more and more to tighten the turn. You should reach a point where your board resists leaning any further without contacting the wheels. Change directions while you pay attention to how tight you’re able to turn.
How tight do you tighten skateboard trucks?
Your trucks should be loose enough that you don’t need to tic-tac to get around obstacles while skating around. Skateboard trucks can be set tight or loose, depending on the rider’s preference. That being said, they should be tight enough that the kingpin won’t fall out and loose enough that the bushings don’t burst.
Is it better to skate loose or tight?
Tight trucks are better for the ancles, it will prevent future injuries, and if you have one a board with tight trucks will help you to get back sooner than you think. On the other hand, loose trucks won’t make it difficult to line up on an obstacle.
What tool do you use to tighten skateboard trucks?
Luckily, loosening and tightening your trucks is very simple, so you can easily make adjustments on the go and continually tweak it. All you need is a skate tool, socket set or spanner to turn the kingpin nut on the underside of your trucks.
Why is my skateboard so wobbly?
Wobbly skateboards are caused by bushings being too soft or the skateboard trucks being too loose. With just a few minor adjustments to the kingpin nut, you can solve this problem. It’s really easy to fix actually and some don’t even consider it a problem. Some people like loose trucks and others prefer them tight.
How wobbly should a skateboard be?
The trucks should be as loose as you feel comfortable when you’re first starting out. Be sure not to compress the bushings when adjusting your trucks. Once you’re comfortable with your board, loosen your trucks up a hair so that they feel slightly uncomfortable.
How can I make my skateboard more stable?
The easiest option to make your TKP more stable (ie, make your skateboard stable), is to simply tighten down the kingpin nut. Doing this makes the bushings deform and bunch up, and it makes your truck feel more stable.
What’s the difference between loose and tight?
Tight means fixed or firmly in place, fully stretched or fitting close to the skin. In slang, it means very good or emotionally close. 2. Loose means not fastened or fixed in place and not tight-fitting.
Why do my skateboard trucks lean to one side?
If your skateboard is constantly turning or leaning towards the left or the right, there are a couple of possible causes. The most likely ones are either the bushings in your trucks, or your hardware. Bushings are the hard, rounded plastic pieces in your trucks that squash down in the direction you are turning.
Why is my skateboard so loud?
The noise comes from your wheel seats, it’s the space between the outer ring of your bearings and the inside of your wheels. If you’ve been skateboarding for a while and haven’t replaced your wheels yet the seating can develop gaps. The bearings shift a little when you ride but more so when you make a turn.
Is it harder to Ollie with loose trucks?
Loose trucks are harder to skate than tight trucks. There, I said it. That’s not to say that tight trucks are easier, or that loosening up the kingpin nut a few turns is going to make you lose all your tricks. I’m talking about skating them loose enough to wobble when you shake the board side to side.
What happens if your trucks are too small?
What Happens When Your Trucks Are Too Narrow. When you’re trucks don’t match your board and aren’t wide enough you’ll get the carpet riding effect. You won’t be able to see your wheels, just your deck. Just a tad too small doesn’t really matter but at a certain point, you’ll run into trouble.
How can I tighten my truck without a wrench?
Use a skate tool or other useful tool to tighten or loosen the big nut in the center of the truck. This single bolt controls the tightness of the trucks. It points directly to the ground when you’re skating, and is found between the wheels. Turn it clockwise to tighten the trucks, getting tighter turning.
Can you over tighten trucks?
Over tightening can increase both the chance that the truck will crack and the chance that the screw will pull out.
Can you tighten trucks with a wrench?
To tighten the trucks on your skateboard: Use a skate tool or socket wrench to turn the kingpin nut ¼ turn clockwise on the kingpin. Move the truck around again to see how it feels. Turn the kingpin nut another ¼ turn clockwise if you want it tighter.
How do I make my skateboard not wobble?
Get low, relax your legs and focus on keeping your upper body over your board and positioned slightly forward. Attack the hill and if your board starts to wobble, stay relaxed and confident. Practice Slowing Down & Stopping!.
