Table of Contents
Thompson’s WaterSeal includes a complete line of deck sealers and stains for protecting deck wood from moisture and sunlight. Applying a sealer and/or stain typically is recommended every one to three years, depending on the finishing product, deck use, weather conditions, and sun exposure.
How long does Thompsons Water Seal last for?
If applied correctly, Water Seal will last up to 4 years. This is dependent on conditions such as orientation of the wall and local climate.
Can you use too much Thompson Water Seal?
If over-application occurs and there is puddling of the product, redistribute product within 15 minutes to a dry area or wipe off. Q: Will the formula of Thompson’s® WaterSeal® Sport Seal® or Fabric Seal change the feel of the treated surface? No. These products will not change the surface’s feel or leave it sticky.
Does Thompson Water Seal need two coats?
One coat is enough, but if more color is desired, a second coat can be applied within two hours before the first coat has dried. With Thompson’s® WaterSeal® Waterproofing Stains, you can clean your tools with soap and water.
How many coats of Thompson Water Seal do I need?
Apply 2 coats using brush,roller or sprayer. note: Use at full strength.do not dilute. The second coat should be applied when the first coat has soaked in the surface. For best results do not leave the first coat to dry for more than 1 hour before applying the second coat.
Is Thompson water Seal any good?
– Thompson’s® WaterSeal® Clear did not alter or change the appearance of the wood. After full drying, we tested the ability to repel water. Water did bead on top of the finish and did not absorb into the wood. – As far as we can tell, Thompson’s® WaterSeal® does not prevent UV graying at all.
What is the best way to apply Thompson’s water Seal?
The fastest way to apply is with a pump-up sprayer (using a coarse setting), but you can also apply with a brush or a roller. You should apply liberally. In the case of areas with heavy discoloration or dirt, apply a second coat, brush lightly with a broom and hose off.
How long does Thompson water Seal need to dry before rain?
Allow at least 48 hours to dry; however drying time will vary depending on the substrate, temperature, and humidity.
How do you remove Thompson’s water Seal from skin?
Soak your hands in warm water for about five minutes. This helps soften the skin and loosen the Seal-It. Dry hands on a towel, then rub a drop of hand lotion over the area with the Seal-It on it. Gently wipe off the lotion to remove the softened Seal-It.
Is Thompsons oil or water based?
Thompson’s® WaterSeal® Penetrating Timber Oil is an oil-based product that provides protection by penetrating into wood pores and sealing out water infiltration. Thompson’s® WaterSeal® Waterproofing Stains are water-based products that have film-forming properties to protect the wood by repelling water.
How much does Thompson’s Water Seal Cover per gallon?
Approximate Coverage Material Approximate Coverage (sq. ft./gal.) Wood: Rough Sawn 100 Wood: Smooth Finish 200 Plywood 150 Wood Shingles 100.
How much area does a gallon of Thompson’s Water Seal cover?
Normally, you’d need to wait for the deck to dry out completely, but not with this product. The next step is to measure the square footage of your deck. That determines how many gallons of stain are required (each gallon covers up to 400 square feet). You can buy it and be on your way.
How much water seal do I need?
Remember that sealers will require multiple coatings, so you’ll probably need at least two gallons for most projects. A gallon only covers so many square feet: One gallon of sealer covers 200-300 square feet. One gallon of waterproofing covers 100-200 square feet.
Should I use Thompson Water Seal on pressure treated wood?
Although the wood is resistant to rot and insect attacks because of the pressure treatment, it can warp, split and develop mildew if not protected from the effects of water. The directions for some, such as Thompson’s Water Seal, specify pressure-treated wood as a suitable use.
Is Thompson Water Seal milky white?
Thompson’s Water Seal Advanced Natural Wood Protector goes on milky but dries clear.
What is the best sealant for pressure treated wood?
Best Deck Sealers for Pressure-treated Wood Ready Seal 520 Exterior Stain and Sealer for Wood. SEAL-ONCE Nano+Poly Ready Mix Penetrating Wood Sealer. #1 Deck Premium Semi-Transparent Wood Stain for Decks. Thompsons Waterseal Solid Waterproofing Stain. Eco Advance Wood Siloxane Waterproofer Concentrate.
Can you use a roller to apply Thompson’s Water Seal?
All Thompson’s WaterSeal products are DIY-friendly, and most need only a single application on a clean, dry deck. You can apply some products with a garden sprayer or paint roller, but for classic deck stain, a paint pad on an extension pole is best.
Can you use a sprayer to apply Thompson’s Water Seal?
Can You Apply Water Seal with Sprayer? Answer: The Thompson Water Seal manufacturer recommends that you use the stain with a plastic sprayer. While you can still apply the sealer with a paintbrush, a good sprayer is will be more efficient.
Is it better to stain or seal a deck?
Sealing a deck is best for cedar, teak, mahogany, or other quality woods as it enhances the wood grain and natural color. Staining a deck protects the wood from mold, mildew, moisture, and rot, and UV rays and sun damage.
Why is Thompson water Seal not drying?
In many cases, high levels of moisture in the air (or worse, rain) may cause the water seal to take longer to dry. Applying water sealant on wet wood or during a moment of very high humidity will not weaken the sealant, though. After two to three days, you probably won’t have any stickiness left on your wood.
What happens if it rains after you seal your deck?
Rain will damage the finish of any wet sealer with linseed oil or mineral oil in it. Because it forms a coating, it takes several hours to dry, and during that time, the sealer is vulnerable. After the rain has passed and the deck has dried, take a closer look.
Is Thompson’s Water Seal good for concrete?
Provides proven waterproofing protection for all masonry surfaces including pavers, brick, concrete, stone, stucco, clay and quarry tile. Use for concrete waterproofing and as a brick sealer.
Is Thompson’s Water Seal toxic?
Environmentally safe, will not harm plants, pets, fish, livestock, humans. Contains zero volatile organic compounds (VOC). No toxic fumes. Seals and protects with single application on most surfaces.
What are active ingredients in Thompson’s Water Seal?
Chemical Composition/Ingredients Propane 000074-98-6 200-827-9 Butane 000106-97-8 203-448-7 Solvent naphtha, petroleum, medium aliphatic 064742-88-7 265-191-7 Distillates, petroleum, hydrotreated heavy paraffinic 064742-54-7 265-157-1 Solvent naphtha, petroleum, light aromatic 064742-95-6 265-199-0.
