Table of Contents
Depending on where you live and the part of your home you’re insulating (walls, crawlspace, attic, etc.), you’ll need a different R-Value. Typical recommendations for exterior walls are R-13 to R-23, while R-30, R-38 and R-49 are common for ceilings and attic spaces.
Which is better R13 or R19 insulation?
Inside your home, the warmer air is higher pressure air, and wants to move, or transfer to lower pressure, cooler air outside. Insulation in your walls and ceilings slows down this heat transfer. So R19 is better insulation than R13, and R30 is better than R19. The larger the R value, the better the insulation value.
What is r12 insulation used for?
Description. This Johns Manville insulation was created for walls and attics to improve energy and acoustic efficiency. You will appreciate the flexible material made of fibreglass without formaldehyde and resistant to fire and mildew.
What is R30 insulation used for?
R30 insulation is the minimum insulation recommended for an Attic from climate zone 1 to 3, while it can be used in cathedral ceilings in all climate zones across the USA. It can be used as maximum insulation in climate zones 4 – 8 of the USA for floors.
What insulation has the best R value per inch?
Vacuum insulated panels have the highest R-value, approximately R-45 (in U.S. units) per inch; aerogel has the next highest R-value (about R-10 to R-30 per inch), followed by polyurethane (PUR) and phenolic foam insulations with R-7 per inch.
Is R 13 or R-15 better?
Is R15 Better than R13? Answer: There isn’t much difference between R13 and R15. However, higher R values offer higher performance. Therefore, in the case of efficiency, R15 is better than R13.
Can you put R19 in a 2×4 wall?
Use R-19 or R-21 kraft-faced fiberglass insulation for two-by-six (2×6) walls. This combination ensures that the insulation is neither too loose nor too tightly packed within the walls. Two-by-four (2×4) stud walls with true 4-inch depth.
What is a good R-value?
Depending on where you live and the part of your home you’re insulating (walls, crawlspace, attic, etc.), you’ll need a different R-Value. Typical recommendations for exterior walls are R-13 to R-23, while R-30, R-38 and R-49 are common for ceilings and attic spaces.
Is R 3 good insulation?
The higher the R-value, the more effective the insulation. 2 to R3. 7 per inch of thickness. With every inch of blown-in cellulose you install, you get that much more in R-value.
What is the R-value of 10 inches of insulation?
R-value of Materials and Depths Material R-value/in 10″ Fiberglass (batt) 3.1 – 3.4 31.0 – 34.0 Fiberglass blown (attic) 2.2 – 4.3 22.0 – 43.0 Fiberglass blown (wall) 3.7 – 4.3 37.0 – 43.0.
How many inches do you need for R30?
For future reference, here is the cavity depth you need for some common insulation r-values: 3.5 inches — R13. 6 inches — R19. 9 inches — R30.
How much space do I need for R30 insulation?
Take a two by two and nail it to the bottom of the rafters. Give yourself another inch and a half, put the R30 in there. All you need is about a half inch to three quarters of an inch air gap in there. You don’t need anything big, and make sure it’s vented.
How much space do you need for R30 insulation?
In order to achieve an R-30 value for blown-in insulation, you will need approximately 8- 1/2-inches of insulation thickness.
Is R30 enough insulation?
The average recommended level is 14 inches of R49. In Zone 2, the average minimum requirement for attic insulation is 9 inches of R30 fill. The average recommended level is 17 inches of R60. In Zone 3, the average minimum requirement for attic insulation is 9 inches of R30 fill.
Is higher R-value better?
“R” means resistance to heat flow. Here’s what to know: The higher the R-value, the greater the insulating power. Almost all insulation products have to tell you their R-value — including duct wrap.
What is the thinnest most effective insulation?
Thermablok® Aerogel is a revolutionary advancement in thermal technology offering the thinnest insulation available to prevent thermal and cold bridging. Classed as a Super Insulation, Aerogel has the highest insulation value of any known material with the lowest thermal conductivity value of any solid (0.015W/mK).
Is R 15 insulation good?
R15 insulation has good thermal resistance, whereas the thermal resistance of the R13 insulation is slightly lower. R15 insulation is commonly used in exterior walls, attics, and floors, whereas R13 insulation can be used in floors and exterior walls.
What is the highest R-value for insulation on 2×4 wall?
A 2×4 wall cavity can be insulated from R-13 to roughly R-25. A 2×6 wall can be insulated from R-19 to R-39.
Is R-13 wall insulation good?
The U.S. Department of Energy gives R-13 insulation a designation of “good” for use in walls in southern regions of the country.
What is R-15 insulation used for?
R-15 EcoTouch® insulation is intended to be friction-fit between exterior wall wood studs. Standard R-11 batts require the use of thick foam sheathing to achieve the recommended R-19 thermal performance.
What is Kraft-faced insulation?
Kraft-faced insulation includes a paper vapor retarder, which helps prevent mold and mildew. Kraft-faced insulation should be installed in exterior walls, exterior basement walls, and attic ceilings by pressing the product into the wall cavity with the paper side facing outward, towards the installer.
