QA

What Is Drip Edge On A Roof

Drip edge is metal flashing installed at the edges of the roof to keep water away from your fascia and from getting underneath your roofing components. If your roof doesn’t have drip edge, water gets behind your gutters and rots out both your fascia board and roof decking.

Do I need a drip edge on my roof?

Without a drip edge, water may end up beneath the shingles and may cause damage to various parts of the home. Though your home may not have originally had a drip edge installed, drip edges are now required by most building codes across North America to protect homes from damage.

Can drip edge be installed after shingles?

The drip edge is often replaced when new shingles are installed, but it can be replaced at any time. Asphalt roof shingles can become brittle in cold weather, so wait until a warm (but not hot) day to remove and replace eave stripping.

Where do you put drip edge on a roof?

The correct placement of a roof drip edge is on top of the roof’s exterior cover directly between the sheathing and the fascia board, which forms a drainage gap between the drip edge and the fascia board. As a result, the drainage improves water flow and protects the roof from potential water damage.

Do you need to replace drip edge when replacing roof?

Do you need to replace it when replacing the roof? No you do not have to replace it but you should, the old drip edge is most likely “old” looking and dirty from being outside for so long. If you are making the effort to replace you roof, you should replace everything so the entire roofing system looks nice.

Do gutters need to be removed to install drip edge?

It is recommended that gutters are placed under or ‘behind’ the drip edge of your roof. If gutters are installed below the drip edge, water can drip behind the gutter and cause damage to the wood supporting the gutter system.

What is the difference between drip edge and gutter apron?

The most obvious attribute that distinguishes a gutter apron from a drip edge is the fact that a gutter apron is more of an L-shaped metal rather than a T. A gutter apron also comes in metal strips with aluminum and steel sheets. Like drip edge, a gutter apron may be available in many different colors.

How much does it cost to have drip edge installed?

The cost of drip edge Drip edge is always going to be included in your roof replacement. Because of this, it’s going to have an impact on the price you’ll pay for your new roof. The standard drip edge used (aluminum) is going to be around $2.00 a linear foot, including labor to install.

Does drip edge go on all sides?

Drip edge is installed around the whole perimeter of the roof. It is used to hold the underlayments down and create a watertight seal around the edge of the roof. Only the face of the metal is seen and is usually just white one to one and half inch stripe located right under the shingles and above the fascia.

Does drip edge go under tar paper?

The drip edge should be over the paper at the eaves, and under along the rake. mroberson: Its a TRAP! Back in my construction days, I learned that you place the tar paper OVER the drip edge on the eaves so if moisture gets through the shingles, it does not get under the drip edge.

Does drip edge go on first?

Installing roof drip edge flashing properly The best way is to install the roof drip edge only along the eaves first, then place ice-and-water barrier (in the snowbelt) or felt paper (underlayment) over the drip edge. This lets any water that gets on the roof run down the underlayment and over the drip edge.

Does drip edge go on rakes and eaves?

It’s important to understand that drip edge installation is different for eaves and rakes. After your roof deck has been prepared, and before you install underlayment, you need to install drip edges at the eaves. You install drip edges on the rakes after you install the underlayment.

Do you need drip edge on rake edge?

A drip edge should be installed on the eaves and rakes of the roof, flush with the decking and fascia. On eaves, the drip edge is installed directly to the deck with underlayment installed over it for proper water shedding. 2×4” drip edge should be used on the eaves and 2×2” may be used on the rake.

Which goes first gutters or roof?

While there is no perfect way to approach exterior remodeling, when it comes to gutters versus roofing, your best bet is usually to go with a new roof first. If your gutters are damaged or ineffective, you may have no other choice but to have them installed before your new roofing system.

How much should shingles overhang drip edge?

Shingles should not extend more than 3/4” (19 mm) past the drip edge. If shingles overhang the edge of the roof by more than 3/4” (19 mm), then they are not supported and may crack and break off. In addition, the wind resistance at the roof edge may be compromised.

Why does water leak behind my gutters?

Water Gets Behind the Gutter If water is dripping behind your gutter, it’s probably because it was installed without any flashing over the back of the gutter. The gutter apron will prevent the dripping. A gutter apron is a bent piece of flashing that tucks up under the shingles and over the gutter. aluminum flashing.