Table of Contents
Do all gas water heaters have a pilot light?
* Caution: Most modern water heaters no longer use standing pilots. They use electronic ignition to ignite the gas. Do not attempt to manually light an electronic ignition system.
Can I relight the pilot light by myself?
If your pilot light goes out, your furnace will not be able to produce heat because its burners will not ignite. Often, homeowners can relight the pilot themselves.
How do I know if my gas hot water heater is on?
Start by looking for an access panel on the side of the water heater. If you remove it and see a blue flame, that’s a pilot light, which only gas models have. Connected pipes are also indicators of gas, while an electric water heater will simply have a cord going into the top or side of the unit.
How do you light a water heater without igniter?
Lighting with No Igniter Take a long lighter to reach the pilot. Remove the plate attached below the dial box. Switch Pilot to OFF. Wait for a while, – 5-10 minutes until there won’t be any gas. Change the temperature to LOW, and switch to Pilot. Push ON/OFF dial down, and simultaneously use the lighter.
Does gas still flow when pilot light goes out?
If your pilot light repeatedly goes out, this is a likely culprit. If this flame sensor should fail, gas will continue to flow even after the pilot light has been extinguished, causing a safety hazard, and requiring immediate repair.
How do you light a gas water heater with electronic pilot?
Turn the gas knob to “Pilot,” press and hold it down. This will start the flow of gas so you can light the flame. Some water heaters have a separate button for pilot mode, usually a red one, which you’ll press and hold. While still holding the gas down, light that pilot.
How do I turn on my gas heater in my house?
How to Turn On a Wall Heater To turn on your gas heater, locate the knob for starting. Turn the knob to “Pilot,” and then push down on the “Ignite” button. Once the pilot light comes on, hold down the Ignite button for 10 to 15 seconds. Set the temperature on the wall heater to your desired heating level.
Should the water heater be on pilot or on?
You should set the water heater to “pilot”. If, however, your water heater is also the boiler for your central heating, then you’ll want to leave the heating running as normal so that your house doesn’t get damp as a result of cold and condensation.
How do I know if my pilot light is on?
If your pilot light is on, it should be easy to see – your eyes will be drawn to the little flame. If you don’t see a flame, your pilot light is out. If there is a flame, check the color. Pilot lights should always be blue.
What does the pilot light look like?
A proper pilot flame should be blue with a yellow tip and should be strong enough to cover about 1/2 inch at the end of the thermocouple tip. If the flame is too strong and improperly adjusted, it will be blue but may be noisy and lift off the thermocouple, causing improper furnace operation.
How do I get my pilot light back on?
How Can I Restart My Pilot Light? Step 1: Turn off your furnace. Step 2: Locate your gas valve. Step 3: Hold down the red button. Step 4: Light the pilot light. Step 5: Let go of the button. Step 6: Turn your gas back on. Step 7: Turn your furnace back on.
How do you light the water heater?
Turn the water heat dial to Low and the On/Off/Pilot dial to Pilot. Then, turn the On/Off/Pilot dial downwards and push the igniter button at the same time. Let go of the igniter button, but keep pressing the Pilot dial downward for around 30 seconds. You should hear a “whoosh” sound when the gas is lit.
How do you light a pilot light on a lighter?
With the button depressed, hold the lighter flame near the pilot opening. Continue holding the gas valve to the “Pilot” position for at least one minute after relighting the flame. This allows the thermocouple safety sensor to heat up properly.
Why is my gas hot water heater not getting hot?
No Flame – Many gas water heaters have a pilot light that will ignite the burners when the unit is turned on. If the water heater has a bad thermocouple (the part that shut off the gas when no pilot flame is present), it can also extinguish the pilot light. Look to have the thermocouple replaced.
Why is my gas hot water heater not heating?
No Hot Water — Gas Water Heater. If a gas water heater isn’t heating, a common problem is usually that the pilot light has gone out. This may be caused by the gas valve, the natural gas supply, or—more likely—the thermocouple located next to the pilot light.
Is there a reset button on a gas water heater?
A water heater reset button, usually red, is located in the center of the limit switch just above the water heater thermostat. The water heater limit switch is a safety device that will shut the power down to the water heater if something malfunctions and the water gets to hot.
