Table of Contents
How deep does a wedge anchor need to be?
A 5/8” concrete wedge anchor requires a 5/8” hole to be drilled into the concrete. The hole in the concrete needs to be drilled a minimum of 1/2” deeper than the concrete wedge anchor will penetrate into the concrete.
How long of a wedge anchor do I need?
As a rule of thumb, the space for the nut and washer is equal to the diameter of the wedge anchor being used. For example, if a 2×4 is being fastened to concrete with a 1/2” wedge anchor then the minimum length of wedge anchor would be 1-1/2”(2×4) + 2-1/4”(minimum embedment) + 1/2”(space for nut and washer) = 4-1/4”.
What are wedge anchors used for?
Concrete Wedge Anchors are heavy-duty anchors used to secure materials and equipment to solid concrete masonry surfaces. They are extremely popular and are one of the strongest anchors for hold strength. Wedge anchors look and function like a sleeve anchor but have a much smaller sleeve near the anchor’s bottom.
Which is better wedge anchor or sleeve anchor?
Because of the surface area available in the design , the sleeve anchors hold better and may even work best where the material is not very stable or drilled well . On the other hand the wedge anchor will work very well in precision drills and will provide strong and reliable locks.
How much weight can a 5’8 wedge anchor hold?
Technical Specifications for Wedge Anchors Size Minimum Embedment Shear (lbs.) 5/8” 2-3/4” 6198 3/4” 3-1/4” 9378 7/8” 3-7/8” 13687 1” 4-1/2” 17712.
How strong are concrete wedge anchors?
Wedge Anchor Holding Values The holding power of the wedge anchor, as with any anchor, is always dependent on the quality of the concrete. As a rule of thumb, a safety factor of 4:1 or 25%, is generally accepted as a safe working load.
What is the difference between wedge and expansion anchors?
The wedge anchor can only be used in solid concrete. Wedge anchors are designed not to be used in other masonry materials such as brick or hollow block. The expansion clip on the wedge anchor is placed on the anchor body in a manner and location that makes the expansion tolerance location critical.
Will wedge anchors crack concrete?
Drop-in anchors and wedge-type anchors, for example, are now “unqualified” for cracked concrete. In addition, most adhesive anchors are not acceptable for use in cracked concrete.
What grade are wedge anchors?
Wedge anchors are available in many types of finishes and material grades. The four most common types are: zinc plated low grade carbon steel, hot dipped galvanized, 304 stainless steel, and 316 stainless steel.
How do wedge anchors work?
A very simple mechanism allows excellent consistent holding values in concrete to be achieved. Once inserted into the hole in the concrete, the nut is turned clockwise. This action pulls the anchor body up, which slides the expansion clip down the cone-shaped working end of the wedge anchor.
Can you use wedge anchors in stone?
Wedge and Sleeve Anchors A bend in the shaft compresses against the sides of the hole as the anchor is driven in with a hammer. You can use these anchors in concrete, block, brick or stone. Many are intended for light loads.
Can wedge anchors be used in brick?
In the case of what would appear to be solid brick, the wedge anchor should not be used because although the brick may look solid, it may be too porous to meet the requirements needed for installing a wedge anchor. Instead, the Sleeve Anchor is an expansion type anchor that should be considered for fastening to brick.
Are Tapcons better than wedge anchors?
Tapcon and wedge anchors are pre-installed mechanical anchors that attach structural objects to concrete structures. However, the wedge anchor suits heavier-duty applications, vs the Tapcon anchor that typically serve lighter deployments.
Do wedge anchors need epoxy?
The only way an epoxy anchor is going to be as strong than a wedge anchor is if the hole is conical so it literally can’t pull up through the hole, and then they still aren’t any stronger than a wedge anchor. It certainly wouldn’t hurt to use epoxy with a wedge anchor.
What is stronger wedge anchor or drop in anchor?
Drop-in anchors are sometimes confused with wedge anchors. While they both work the same way — they expand and fill the inside of a hole in concrete — the wedge anchor features a conical-shaped hollow bottom. Wedge anchors are usually the better option for applications involving heavy bearing loads.
What size drill bit do I need for a 3/8 wedge anchor?
The correct drill bit size for a 3/8″ wedge anchor is 3/8″. In this case, the bit size is the exact same as the anchoring diameter.
How much weight will a 3/8 drop in anchor hold?
Additional Information Bit Size: 1/2″ 2000 PSI Concrete – Pull-Out (lbs.) *: 1170 Type: Female Diameter: 3/8″ Length: 1-9/16″.
What size drill bit do you use for a 3/8 wedge anchor?
1. Drill hole into the concrete using a carbide tipped bit. Bit size = 3/8” (same as anchor diameter) Drill the hole at least 1/2″ deeper than the length of the anchor.
Are wedge anchors Good?
Heavy-duty applications require sturdy hardware like Bolt Dropper’s Stainless Wedge Anchors. These wedge-type anchors feature all stainless steel construction, making them highly corrosion resistant and durable.
How soon can I put anchors in new concrete?
It normally sets in 10 to 30 minutes. After an hour or so, QUIKRETEâ Anchoring Cement will have set sufficiently to screw most types of anchor bolts home. For extreme loads, wait 2 hours before applying load to the anchor. Within 24 hours, QUIKRETE® Anchoring Cement reaches pull-out strength of 12,500 psi.
