Table of Contents
Insert a paper clip, or a similar sized object, into the reset hole on the controller (depicted below). Using the paper clip, press and hold the reset button inside the reset hole for eight (8) seconds. If done successfully, the light strip will flash five times then cycle through the colors blue, green and red.
How do I reset my LED strip light remote?
Step 1, Make sure all part of the LED strips kit are connects right and powered. Step 3, Press the “FADE7” button ,it will flash one second. Step 4, Turn on the LED strips again, press Red, Green, blue button one by one, it will change to its original color.
How do I reset my LED light bar?
Plug and unplug the power adapter and turn on and off the light for 5 times continuously (turn on and off for 2 seconds each time), and the display hanging lamp will show breathing effect. After breathing for 5 seconds, the lamp will automatically restart, that is, the lamp has been restored to the factory settings.
Why are some of my LED lights different colors?
Not Enough Air Ventilation As established above, when LED strip lights don’t get enough cooling, they get overheated, and the diodes can change color. One of the biggest ways this can happen is poor air ventilation around the lighting setup. All spaces would not allow proper air ventilation to occur.
Do LED light strips get hot?
How warm an LED strip gets during operation will depend on the LED strip design and quality, as well as the ambient temperature. In other words, for an LED strip in a typical room temperature environment of 75°F (24°C), you can expect the LED strip to reach a temperature of 129°F (54°C).
Why won’t my LED lights change color?
Bad Pin Connection – If your LED strip light fails to turn on at all, then check your pin connections. If your RGB strip lights won’t change colors try flipping your strip light around and reconnecting it. Incorrect Power Source – Make sure to double check which power source your lights require.
Why did my LED lights suddenly stop working?
Heat buildup, screwing bulbs too tightly, or placing LEDs in improper electrical circuits and accessories are common causes of LEDs stopping working. In addition, poor quality capacitors, drivers and diodes are also leading factors in reducing the life of LED bulbs.
Why won’t my LED lights respond to the remote?
If your remote control suddenly stops working or your lights start blinking, you may need to reset the controller and pair it back to the receiver unit. The controller sometimes un-pairs itself from the receiver due to a loose connection, radio interference from an external source or a low battery in your remote.
Can you cut LED strip lights?
Can I Cut The LED Strip Light Anywhere Else? You can, but we wouldn’t recommend it. By cutting an LED strip light anywhere other than the designated cutting point, you run the risk of damaging the components on the strip itself, as well as the circuit board. This may ultimately result in the strip light not working.
How long do LED lights last?
One of the biggest advantages of LED light fixtures, is their extended lifespan. While incandescent light bulbs were built to last around 1,000 hours, the most enduring LED light fixtures have been tested to last as long as 100,000 hours. On average LED light bulbs will not have to be changed for at least 20 years.
Why are my LEDs only green?
Check for solid connections to any power supply. Check for tears in the LED strip, especially just before the strip misbehaves. A tear or bad solder joint could have removed the R and B channels (depending on how the manufacturer put the LED strip together. If its like in the image, the LED strips.
Can LED cause fire?
Because of this, LEDs produce far less heat than other light bulbs, and heat is how fires start. Therefore, though an LED might feel warm to the touch, it is extremely unlikely that an LED would start a fire.
Do LED lights burn out?
Unlike incandescent light bulbs, LEDs don’t produce light using heat. This is part of what makes them so energy efficient. The downside is that their components can be sensitive to overheating, which can cause them to burn out prematurely.
Do LED lights use a lot of electricity?
In general, LED Lights use less electricity and last longer than incandescent or CFL bulbs. LED lights also use very little electricity in comparison to traditional incandescent bulbs.
What app do you get for your LED lights?
What is Lumenplay®? Lumenplay® is an extendable string of app-enabled RGB LED lights that enables you to create scenes of color and motion, all from your smart device. Use the free Lumenplay® app to setup a personalized light show by choosing color combinations, effects, speed, direction and brightness.
Why are my blue LED lights not working?
If the LEDs will not light up at all, then this could be down to a faulty power supply. Solution: If you have several power supplies, then try a different power supply onto the same strip to see if this now works. If it does, then you have a faulty power supply and will need a new one.
How long do LED strip lights last?
LEDs have an unbelievably long expected life-span, compared to both incandescent and fluorescent lights. With an average life-expectancy of some 50,000 hours, LED strip lights will still be burning bright in 17 years’ time, long after their traditional counterparts will have expired.
