Table of Contents
How do I open my inground pool?
How to Open Your Inground Swimming Pool Get the Gunk Off Your Pool Cover. Whisk Away the Winter Pool Cover. Clean and Store Your Pool Cover. Skim the Pool. Remove Plugs and Ice Compensator. Reinstall the Chutes and Ladders. Just Add Water. Set up and Run Your Filter and Pump.
What chemicals are needed to open an inground pool?
Chemicals Checklist: Everything You Need to Open Your Pool A good test kit or test strips for checking your pool’s pH, calcium hardness, total alkalinity, and chlorine levels. Chlorine granules or tablets. Shock treatment. Increaser/decreaser chemicals for alkalinity, calcium, and pH. Algaecide. Stain treatment.
How do you open an inground concrete pool?
14 steps for opening your inground pool Remove leaves & water from your pool cover (or safety cover) Remove your winter cover. Clean & stow away your pool cover. Fill up your pool. Remove winter plugs & re-install skimmer baskets. Re-attach deck equipment. Set up your filter & pump. Power-on your filter & pump.
What chemicals do you add first when opening a pool?
Chemicals Needed for Pool Start Ups Stain & Scale Preventer. Granular Shock Chlorine. Chlorine Tablets. pH Increaser and/or pH Decreaser. Alkalinity and/or Calcium Increaser. Cyanuric Acid (Stabilizer) Algaecide and Clarifiers if needed. Complete Test Kit or Test Strips.
How much shock Do I need to open my pool?
To shock your pool, use 2 pounds of shock for every 10,000 gallons of water, which should raise your chlorine levels to 10.0 ppm. Depending on your pool, you can use either Leslie’s Power Powder Plus or Leslie’s Chlor Brite.
Should I shock my pool when I first fill it up?
At first you’ll add chlorine in what’s called “shock” levels – an extra heavy dose to start your pool off. A shock dose coupled with extra circulation will ensure that all the water gets treated properly in the beginning. Now it’s time to keep the water hardness in check, otherwise known as alkalinity.
How long does it take for pool to clear after opening?
As a general rule of thumb a DE filter can clear up a pool within 1-3 days, a sand filter 5-10 days, and a cartridge system can vary widely based on the size and condition of the filter elements, and how often they are disassembled and cleaned.
How do I open my pool for the summer?
Your Swimming Pool Opening Checklist Remove, Clean and Store Your Pool Cover. First, remove your pool cover, clean it and store it away securely. Fill Your Pool Up. Clean Out Debris. Inspect and Clean Your Pool Filter. Reinstall Plugs. Prime Your Pool Pump and Filter. Test and Balance the Pool Water. Shock Your Pool Water.
How do you reopen a pool?
How to Reopen Your Pool Drain Water Off the Cover Before Removing It. Store Your Pool Cover Properly. Reconnect All Disconnected Equipment. Replace Winterizing Drain Plugs with Summer Plugs. Remove Metal Stains. Test and Balance the Water. Brush and Vacuum the Pool. Shock the Water to Kill Bacteria.
What order do you balance pool chemicals?
7 Steps to Balance Pool Water Test and Adjust Total Alkalinity. Test and Adjust pH. Measure and Adjust Calcium Hardness. Add Sanitizer to Your Water. Check and Adjust Cyanuric Acid. Measure Your Water’s Total Dissolved Solids. Shock Your Swimming Pool.
What happens if you get in a pool that was just shocked?
What can happen if you go into a pool too soon after it’s been shocked? There are a few potential issues. “Chlorine will react with water to produce an acid,” Alan says. “The effects will be different depending on whether chlorine is inhaled or whether there is skin or eye contact.”May 25, 2021.
Can you shock a pool without the pump running?
It all depends on the type of pool and the chemical levels in the pool. Your pool can keep running for a few days with no problems while without a pump. However, know that a standard pool needs a pool running for at least once in 24 hours, or you might notice an algae bloom.
How do I open my pool in the spring?
Shocking your pool. Drain and Clean the Pool Cover. Remove the Pool Cover. Clean and Store the Pool Cover. Raise the Water Level Back to Normal. Reconnect the Pool Equipment. Remove Winterizing Plugs from Skimmer and Return Lines. Turn the System Back On. Add MetalFree to Prevent Staining.
How much does pool Dewinterization cost?
Cost to Close a Pool Pool Closing Costs National average cost $250 Average cost $200-$300 Low-end $100 High-end $350.
Why did my pool turn green after I shocked it?
Pools can immediately turn green after shocking when they have metals like copper or iron in the water. These metals oxidize when exposed to high levels of chlorine which makes the pool water turn green. Metals in the water are caused by some algaecides and using well water.
Why is my pool green when I just filled it?
Your first instinct when you fill your pool with new water, is to shock it. But that shock then oxidizes the metals, that chemical reaction then causes the green hue in your water. This is common with refills that used well water or even water that hasn’t been shocked but instead contains a high level of metals.
How do you open an above ground pool?
Step 1 – Clear off the water, debris and anything else from the pool cover. Step 2 – Remove the pool cover. Step 3 – Pull the winter plugs and accessories out. Step 4 – Top up the water in your pool. Step 5 – Reinstall the pool ladder. Step 6 – Prepare the pool filtration system. Step 7 – Power your filtration system up.
