Table of Contents
How do I choose a miter saw size?
Blade size is an important consideration in selecting a miter saw. The most common miter saw sizes are 8, 10 and 12 inches. Keep in mind that larger diameter blades can make longer cuts. Positive stops are factory set points that let you quickly make precise cuts on specific angles.
Is a 10-inch miter saw big enough?
10-inch Miter Saw The 10-inch blade cuts pieces that are up to 6 inches wide, which covers most trim and molding boards. Trim is seldom more than 4 inches, so you’ve got plenty of wiggle room with a 10-inch miter saw. A 10-inch blade will spin faster than a 12-inch blade, resulting in smoother cuts.
What size miter saw for 2×4?
10-inch miter saws are perhaps the most commonly used cutting tools of this kind. A 10” saw can easily do 45-degree miter cuts through 2×4 dense lumber. It’s a relatively inexpensive cutting tool and doesn’t require as much experience or strength to handle.
What size Mitre saw for baseboards?
Compound Miter Saws For precise cuts, a 6-inch baseboard needs to be laid flat in an 8-1/2 inch saw to slice off a partial degree. The larger 10- and 12-inch models allow the 6-inch board to rest upright against the miter fence.
How wide of a board will a 10-inch miter saw cut?
Saws start to differ when you look at their blade diameter—commonly 10 inches or 12 inches. The bigger the blade, the deeper and wider its maximum cut. Typically, a 10-inch miter saw will cut a 2 x 6 at 90 degrees and a 2 x 4 at 45 degrees; a 12-inch miter saw will cut a 2 x 8 at 90 degrees and a 2 x 6 at 45 degrees.
Can a 12 inch miter saw cut a 4×6?
Yes! A 12” miter saw can easily cut a 4 x 6 lumber. A 12 inch miter saw clearly has a bigger blade and has the capability to cut 4×6 lumber in a single pass.
Can 10 inch miter saw cut a 4×4?
It may surprise you to know that the answer in question to cutting 4×4 posts with a miter saw is a hard, YES! If you can give the blade more clearance, then it should be possible to get a clean single pass cut through a 4×4 post, even when utilizing a 10-inch blade.
Can you cut a 6X6 with a 10 inch miter saw?
A miter saw with a 10-inch blade installed can cut a 6X6 lumber piece, only it cannot do so with one single pass. This will require a bit more effort as the blade diameter is quite small for the piece of wood you are cutting.
What is a 10 inch miter saw good for?
Common Uses for a 10-Inch Miter Saw Perfectly angled miter cuts. More complex bevel and compound angle cuts. Cutting plastic and metal pipes to length. Precise repeated cuts.
How wide of a board can a 12-inch miter saw cut?
Manufacturers also make 12-inch versions, which have a maximum cut of about 7 1/2 inches, wide enough for two-by-eights. This larger saw can cut a maximum thickness of 3 1/2 inches, enough to cut through four-by-fours.
Can a 7 1 4 miter saw cut a 4×4?
No not with one cut. You would have to turn the 4×4 over. Blade is a 7 1/4″ diameter, same as a hand held circular saw.
Can you use a jigsaw to cut 2×4?
A jigsaw is a precision tool with a thin blade, which makes them ideal at cutting intricate designs on thin material. If you ever had to cut a 2×4 piece of framing lumber with a jigsaw and thought to yourself “there’s no way”, you might be surprised!.
What type of saw is best for cutting trim?
A miter saw can quickly make the same crosscuts a circular saw can, but its key feature is an ability to make precise angled and beveled cuts. A miter saw is a perfect tool for cutting moulding or wood trim. Miter saws have a gauge on the saw table that lets you set the saw to make accurately measured angle cuts.
What saw is best for cutting baseboard?
Cutting Baseboards with Miter Saw The power miter saw is the most widely used for baseboard cutting. It cuts clean miters or straight, 90-degree crosscuts with precision and little or no splintering or grain-blowout.
What kind of saw do I need to cut baseboards?
The handiest tool is a miter saw. A miter saw will help you quickly and accurately cut trim. Most importantly, it makes quick work of cutting the corners on baseboard moulding.
Which cut is when you cut the board straight with the grain?
There are two types of straight cuts a circular saw can make on a piece of lumber. A crosscut is a cut against the grain of the wood, such as when trimming a length of board to size. A rip cut goes with the grain of the wood and is usually a longer cut.
Is a miter saw worth it?
Miter saws are a valuable tool for the DIYer, and a must-have tool for a fully functioning workshop. They are designed to quickly cut crown molding, door frames, window casings, and picture frames. Miter saws can also make straight cuts for general do-it-yourself woodworking projects.
How long can a sliding miter saw cut?
Sliding compound-miter saws will work just like chop saws, but because their blades move back and forth on horizontal rails, they also can slice stock up to 15 inches wide in one stroke.
Will a 12 inch sliding miter saw cut a 6×6?
The bevel ranges max out at 45 to 48 degrees. Performance and Cutting Capacity. No saw could cut through a 4×4 at a 45-degree bevel angle, nor could any cross-cut a 6×6.
Do you push or pull a sliding miter saw?
Sliding miter saws are designed to cut on the push stroke. Pulling a miter saw through the cut results in a climb cut that could cause the blade to rise up out of the wood and chase after you. Also, it is important to use a blade with teeth that angle forward between 0° and 5°.
