Table of Contents
Your price could vary depending on how much the roofing company charges for labor, but generally, you can expect to spend between $70 to $100 for each sheet of plywood. A 4 x 8 sheet of plywood covers about 32 square feet of roof area—and the average roof measures about 3,000 square feet.
What kind of plywood do roofers use?
CDX is the grade of plywood most commonly used for roofing (CDX plywood means it is Construction Grade for exterior purposes).
How much does a plywood sheet cost?
Cabinet Grade Plywood Thickness Type Price 1/4″ Oak Plywood $25.97 1/2″ Oak Plywood $42.97 1/2″ Birch (3 ply) $41.97 3/4″ Birch (5 ply) $44.97.
What thickness plywood should be used for roofing?
Most Common Thickness The most common rafter spacing is 24 inches, and 5/8-inch plywood is recommended for that. It will support roof loads for most situations and is the standard for most roof applications. Roofs with very heavy loads may require 3/4-inch thickness.
What is the best plywood for a roof?
Builders love plywood for its water resistance, structural stability and low cost. They also love oriented strand board, though. It costs even less and is comparable to plywood on the other two counts, and they increasingly prefer OSB for roof sheathing. Either is an acceptable choice in most jurisdictions.
What is the minimum thickness of roof sheathing?
Sheathing must be a minimum of 19/32-inch thick. Never affix roof sheathing with staples; 8d ring-shank nails need to be used instead. The normal thickness range for sheathing is 3/8 to 3/4 inch.
Is plywood or OSB better for roofing?
Plywood Holds the Moisture Advantage Over OSB When plywood gets wet, it tends to swell. OSB takes longer than plywood to get saturated, but also takes much longer to dry out. When used as roof sheathing, this tendency to hold moisture means it will degrade faster than plywood when exposed to chronic leaks.
What does a 4×8 sheet of plywood cost?
“A sheet of [4-foot by 8-foot] half-inch plywood costs $65 today.
How heavy is a 4×8 sheet of plywood?
A typical 4′ x 8′ sheet of 1/2-inch Pressure-Treated Plywood weighs around 60 lbs.
What is the cheapest plywood to buy?
D-grade plywood: The cheapest type of plywood veneers, these sheets typically haven’t been repaired. The flaws can be slightly larger and the knots in this type of plywood can be up to 2.5 inches in diameter. CDX: CDX-grade plywood is typically inexpensive material, as it is made of the two lowest grades (C and D).
How many sheets of plywood do you need for a roof?
Divide the total roof area by 32 to get the number of sheets you will need to cover the roof. A typical 4 foot by 8 foot sheet of plywood covers 32 square feet. If your roof area is 1,600 square feet, 1,600 divided by 32 will mean you need about 50 sheets to cover the roof.
What’s the best wood to use for a roof?
Cedar has earned a reputation for being strong, flexible, and weather resistant – qualities that make for an effective roofing shingle. Among roofing shingle manufacturers, cedar is the go-to material, all thanks to its durability.
How long does roof plywood last?
There are a few averages you can expect, but they are dependent on these factors. Plywood siding, such as T-111 should give at least a 35 year life expectancy, if finished properly; but there are many cases of it lasting over 50 years. Roof sheathing should last 30 to 40 years or to put it another way, two roofs.
Does roof replacement include plywood?
If you are getting a new roof, while you may not necessarily need to have the plywood decking replaced, you should have it carefully inspected by a qualified roofing contractor. When considering a contractor for your project, be sure to address the subject of plywood replacement, and what the cost per plank will be.
Can you put new plywood over old on a roof?
The new plywood will have to be nailed to the rafters or roof trusses. But, with the old plywood left in place, it will be considerably more difficult to locate the rafters to ensure proper nail placement.
How thick should plywood be for a shed roof?
Plywood thicknesses for roofs start at 3/8” in areas with light load requirements on rafters at 16” centers. Thicknesses of 1/2 to 5/8 inch are common with rafters spaced at 24” centers. For heavy load rated areas, 3/4-inch-thick plywood is recommended, regardless of rafter spacing.
Should you use tongue and groove OSB for roof sheathing?
Tongue & Groove Boards T&G roof decking, however, looks classy and rich. In fact, T&G boards are most frequently used when the sheathing is visible from the inside such as in cathedral ceilings or in some cabin-style homes, especially if the span of the rafters is greater than 2 feet.
How far should roof rafters be apart?
But they do tend to space rafters in one of several industry-standard increments, typically either 12, 16 or 24 inches apart. These spacing intervals are measured “on center,” meaning that the measurement is taken from the center of one rafter’s horizontal surface to the center of the next rafter.
What is the best way to waterproof plywood?
Yes, you can make plywood waterproof by spraying it with liquid latex, waterproof paint, or varnish. You can also coat it with epoxy sealant or hard-drying oil to seal it and make it impervious to water.
Which is cheaper plywood or OSB?
OSB is less expensive than plywood. To build a typical 2,400-square foot home, OSB may cost $700 less than plywood. OSB is considered by many to be a “green” building material because it can be made from smaller-diameter trees, such as poplars, that are often farmed.
What can I use for roof sheathing?
Oriented Strand Board (OSB) or plywood can be used, although plywood will provide higher nail head pull-through resistance. Use panels rated as “Exposure 1” or better. Install sheathing panels according to the recommendations of the Engineered Wood Association (APA). Use panels no smaller than 4 feet long.
What are the 3 types of plywood?
Although specialty plywood can have any number of plies above three, most plywood is categorized as 3-ply, 5-ply or multi-ply. 3-ply is one of the most common types of plywood. It is about 2- to 3-millimeters thick and is generally used indoors, since it looks more decorative than thicker plywood boards.
Does plywood come in 5×8?
The standard thicknesses for plywood are 1 ¼, 1 1/8, ¾, 5/8, ½, 3/8, ¼, and 1/8 inches.
How many sheets are in a bundle of plywood?
Who can tell me why there are 49 sheets of plywood per bundle?Apr 25, 2000.
