Table of Contents
How do you flash a roof against a wall?
Place a kick-out flashing at the base of the roof and flush against the wall. Remove the flashing and apply some roofing cement to fix the flashing into place. Place the first piece of step flashing over the end of the tarter strip. Ensure that the step flashing will lead the water directly into the kick-out flashing.
What flashing is installed where a roof intersects a head wall?
Headwall or Apron Flashing We install headwall flashing, also called apron flashing, where vertical walls intersect the roof. It prevents leaks by guiding water running down the wall onto the roof system. We place headwall flashing behind siding.
What type of flashing should be installed where the bottom of a roof meets a wall?
Step flashing: Step flashing is best for where the roof face meets a wall, for example, where a dormer projects out of the roof. In this spot, it’s possible that water could flow down the wall and slip past the shingles into the building below.
How do you seal roof flashing?
Renew flashing seals by chipping out the old mortar and caulking along the edges of the flashing. Use special masonry caulk to seal the joints between the flashing and the chimney. Seal the seam between the cap and step flashing with urethane roofing cement or silicone caulking compound, as shown at right.
What are the different types of roof flashing?
Roof Flashing Types Continuous Flashing. This is also known as “apron flashing” because it acts in a similar manner to an apron. Base Flashing. Counter Flashing. Step Flashing. Skylight Flashing. Valley Flashing. Drip Edges. Kickout Flashing.
What is drip edge flashing?
Drip edge is metal flashing installed at the edges of the roof to keep water away from your fascia and from getting underneath your roofing components. If your roof doesn’t have drip edge, water gets behind your gutters and rots out both your fascia board and roof decking.
What does cap flashing look like?
Cap flashing: An L shaped structure that lies flat against the roof and other fittings such as windows. The shape of the structure runs water off in the opposite direction. This prevents it from pooling in any cracks around the fitting. Chimney flashing: Flashings need to be applied around chimneys.
What is L flashing used for?
The Gibraltar Building Products L-Flashing protects your home from moisture infiltration where your wall meets your roof. L shaped flashing is a versatile, general use flashing used where a uniform or strengthened finish is needed on a 90° surface.
Does roof flashing need to be caulked?
Roof flashings can be made from thin metal, rubber, and a few other materials. It’s okay to use caulk and roofing cement as a last resort to make a temporary leak repair, but don’t allow a roofer to convince you they’ll work for the long term.
Should you caulk flashing?
It is generally not a good idea to use caulking on wood siding. Flashing acts as a waterproofing layer for this type of siding, and caulking will prevent the flashing from doing its job. As far as trim boards are concerned, you should not caulk around these areas if they sit on top of the surface of your siding.
What is wall flashing on a roof?
What is roof flashing? Roof flashing is a thin metal material that roofers install to direct water away from certain areas (walls, chimneys, roof valleys) of your roof. It’s a crucial roofing material that every roof needs to have. You’ll have different metal options to choose from for your roof flashing.
Where does drip edge go on a roof?
The correct placement of a roof drip edge is on top of the roof’s exterior cover directly between the sheathing and the fascia board, which forms a drainage gap between the drip edge and the fascia board. As a result, the drainage improves water flow and protects the roof from potential water damage.
Should there be a gap between drip edge and fascia?
The best installation method is to leave a gap between the drip edge and the fascia board, about the width of a finger. The shingles should also overhang the drip edge 3⁄8 to 1/2 an inch.
What type of flashing is found along the peak of the roof?
Vent Pipe Flashing This is a special type of flashing that fits snugly over round pipes that pass through your rooftop.
What is an apron flashing?
Apron Flashings are located at the low end of a curb or penetration. This type of flashing makes a water tight junction, basically forming a right angle which starts up behind the cladding, comes down and out and over the roof. An Apron Flashing diverts moisture and is used at junctions between roofs and walls.
What is the difference between flashing and step flashing?
Step flashing is primarily used against the sides of walls and chimneys. That’s why the term “step” is used in step flashing. You do it step by step by installing a shingle, then a piece of flashing, then another shingle, then a piece of flashing until the wall is completely protected.
Where should flashing be installed in a masonry wall?
Flashing must be located beneath the first course of masonry above the finished ground level above the foundation wall or slab and at other points of support, including structural floors, shelf angles, and lintels when masonry veneers are designed per Section R703.
