Table of Contents
Just follow these steps: Measure the area in feet. Multiply length by width, and then by thickness. Divide the resulting number by 27 to find cubic yards.
How many yards of concrete do I need for a 10×10 slab?
The amount you will need for a 10 x 10 slab is 1.3 cubic yards, we always add an extra 10% to allow for any slab depth variations or spills that may occur.
How do I calculate square feet into yards of concrete?
To convert square feet to cubic yards, you simply multiply your square footage figure by the height or depth of the area (in feet) to get a volume measurement in cubic feet. You then divide the total by 27 to get your measurement in cubic yards.
Do you need rebar for 4 inch slab?
The thickness of rebar should be no more than 1/8 that of the slab, so a 4” slab shouldn’t have steel greater than #4 or 1/2″ bar. It’s best to check with a Structural Engineer if your slab will bridge or cantilever. What is this? For 4” concrete slabs used for driveways and patios, #3 rebar is common.
How many square feet is a yard of concrete 4 inches thick?
One Cubic Yard of Concrete: 4-inches thick – covers 81 square feet.
How many yards of concrete do I need for a 24×24 slab?
For example, for a concrete slab that is 24′ X 24′ X 4”, simply enter 4 in the Thickness/Depth field, 24 in the Width field, and 24 in the Length field. Click “Calculate”. Your answer should be 7.11 yards. Note: The Concrete Volume Calculator can also be used to determine yardage for aggregate products.
How much does it cost to pour a 24×24 slab of concrete?
A typical 24×24 garage slab costs between $3,057 and $5,944 with prices ranging from $5.31 to $8.31 per square foot for a 4” reinforced slab of concrete, and $6.83 to $10.32 per square foot for a 6” slab of reinforced concrete.
How many square feet is 4 cubic yards?
Cubic yard to Square feet Calculator 1 cubic yard = 9 ft 2 0.037 cubic yard 4 cubic yard = 22.6786 ft 2 0.2963 cubic yard 5 cubic yard = 26.3162 ft 2 0.4141 cubic yard 6 cubic yard = 29.7173 ft 2 0.5443 cubic yard 7 cubic yard = 32.9338 ft 2 0.6859 cubic yard.
How much weight can a 4 inch slab of concrete hold?
Typically we like to limit the weight to about 40 lb/sqft on an unknown 4″ slab. In most cases you can go to 80 lb/sqft in isolated spots, but unless you know roughly what the soil bearing and reinforcing is for that slab you might be looking at cracking.
Do you need gravel under concrete?
Whether you pour concrete for a walkway or patio, a strong gravel base is required to prevent the concrete from cracking and shifting. Gravel is especially important in clay soil because it doesn’t drain well, which results in water pooling under the concrete slab and slowly eroding the soil as it finally drains.
Which is better rebar or wire mesh?
In summary, rebar vs wire mesh can have costly differences. Rebar remains stronger and ensures consistent contact in the soil where as wire mesh is unpredictable and often results in a week concrete foundation.
How many bags of concrete do I need for a 10×10 slab?
The thickness of your 10′ x 10′ slab will determine just how many bags you need. The average thickness of a 10′ x 10′ concrete slab for a shed is 4 inches thick. At 4″ thick, your 10 x 10 slab will take 56 bags of concrete that weigh 80 lbs.
How thick should a concrete slab be?
Standard concrete floor slab thickness in residential construction is 4 inches. Five to six inches is recommended if the concrete will receive occasional heavy loads, such as motor homes or garbage trucks. To prepare the base, cut the ground level to the proper depth to allow for the slab thickness.
How many 80 lbs bags of concrete make a cubic yard?
One 80lbs bag of Quikrete Concrete Mix will yield approximately . 60 cu ft. So it will take 45 bag to equal one cubic yard of concrete. If you have a project over a 1/2 a cubic yard you should consider our Mix On-site Concrete especially if you are hand mixing.
How do I calculate how much concrete I need?
Essentially you are solving for volume and then converting to cubic yards. For concrete, the formula for volume is as follows: length x width x thickness.Here’s what the math looks like for a 10′ by 10′ concrete patio: 10 x 10 = 100 square feet. 4 ÷ 12 = .33. 100 x .33 = 33 cubic feet. 33 x .037 = 1.22 cubic yards.
How many yards of concrete can a truck hold?
Each cubic yard costs about $65. However, a fully loaded cement truck will hold 10 cubic yards—and partial “short” loads cost $15 to $20 extra for every cubic yard less than a full load.
How many bags of concrete do I need for a 4×8 slab?
As per calculation, for a 4×8 slab at 4 inch thick, generally you will need approximately either 23 bags of 60lb or 18 bags of 80lb of premixed concrete, at 5 inches thick slab, either 29 bags of 60lb or 23 bags of 80lb premixed concrete are required, while at 6 inches thick slab, either 35 bags of 60lb or 27 bags of.
