Table of Contents
Is blown-in attic insulation worth it?
Unless your home is relatively new, you will almost certainly benefit from installing blown insulation in your attic. It will make your home a more comfortable place to be in summer and winter, decrease the cost of your energy bills, and increase the value of your home.
How much does it cost to have blown insulation put in your attic?
Home Advisor estimates that installing blown-in attic insulation costs anywhere from $600 to $1,200 for attics about 1000 square feet in size. The average home should need an R-value of about 30, which means 10 to 14 inches of total insulation.
Do you need a machine to install blown-in insulation?
There are two main types of insulation: batt and roll insulation and loose fill (sometimes known as blown-in insulation): Batt and roll insulation works well between joist and stud spaces or if you have a wide-open space or a crawlspace. If you choose loose fill insulation, you’ll need to rent a machine to install it.
Which is better attic insulation blown or rolled?
Rolled fiberglass insulation scores an R-value of 3.7. So overall, rolled fiberglass insulation is slightly more effective at blocking in and out heat than its blown counterpart.
Should you remove old attic insulation before adding new?
Expert contractors that specialize in insulation advise that removing old fiberglass insulation is best before installing new cellulose insulation because of possible mildew, mold, or rodent excrement. So, by have attic insulation removal service, you are getting rid of those possible issues.
Which is better foam or blown insulation?
Between spray foam and blown-in cellulose, which is better? Both spray foam and blown-in cellulose insulation have their advantages. Spray foam has a higher R-value, so it’s the more effective insulator. But cellulose is better at insulating street noise.
Is blown-in insulation cheaper than rolls?
The Differences Between Blown-in and Rolled Insulation The lower the R-value is, the less effective it will be as insulation – although it will be cheaper as well. In such situations, blown-in insulation is much more effective since it allows you to easily insulate those hard to reach areas.
How deep should my attic insulation be?
The higher the R-Value, the better the thermal performance of the insulation. The recommended level for most attics is to insulate to R-38 or about 10 to 14 inches, depending on insulation type.
How many bags of blown in insulation will I need?
More on Calculating Insulation Needs Divide the measured square footage you obtained by 1,000 square feet to obtain the multiplication factor: 1,500 square feet/1,000 square feet = 1.5. Multiply the R-value chart number to obtain the number of bags (rounding up at the end): 40.8 * 1.5 = 61.2 or 62 bundles.
Can I put plywood over blown in insulation?
Once the insulation is down, you can turn your attic into valuable storage space by covering the floor with plywood. It will also make the attic a safer place in which to walk.
Can you put too much insulation in your attic?
It’s possible to over-insulate an attic as too much will cause moisture buildup and eventually result in mold. Eventually, adding more insulation leads to diminishing returns in trapping heat as well.
Can you add insulation to your attic yourself?
You can install fiberglass batts yourself right over existing insulation, but follow these precautions: Wear a long-sleeve shirt, gloves, eye protection and a dust mask. Make sure you use an unfaced batt (one without a paper or foil layer) so the insulation does not trap moisture in the ceiling.
What type of attic insulation is best?
Many people consider fiberglass batt to be the best attic insulation. It consists of plastic reinforced by small glass fibers. The batt version comes in blanket form — i.e., small, pre-cut sections that you can lay down wherever you need to.
Can I put batt insulation on top of blown-in?
A: There’s no problem with installing fiberglass batts over your existing blown-in insulation. The reason for this precaution is that the facing on the insulation batts is a vapor barrier, which is intended to prevent moisture vapor from penetrating into the insulation.
Does blown-in insulation have asbestos?
If your attic or wall insulation is in batt or blanket form, whether it’s fiberglass, cellulose, or another material, you generally don’t have to be concerned about asbestos2. The types of insulation that were most commonly made with asbestos are loose-fill, also called blown-in, insulation.
How often should attic insulation be replaced?
How often should attic insulation be changed? Even though attic insulation is said to last anywhere from 80 years to 100 years, it does lose effectiveness as its ages. Insulation experts recommend replacing after 15 years to assure it is doing the job you need it to.
Does wet blown cellulose settle?
The cellulose settles a few inches in the first few days. This is the most cost effective method of installation. We recommend a settled depth of 16″ or R60.
What are the disadvantages of cellulose insulation?
Cons of Cellulose Insulation It generates a lot of dust during installation. It is heat-resistant and has a high R-value. Cellulose insulation is prone to sagging and settling. It is heavily treated with fire-retardant chemicals.
