Table of Contents
PREP – Wait 4-8 weeks after new deck is built. Sweep away any leaves or other debris. WATER DROP TEST – Deck is ready when droplets are absorbed. STAIN – Apply even coat with wood grain. Work in with brush. Wait 4 hours between coats. Wait 24-48 hours before enjoying.
Does a new deck need to be cleaned before staining?
In short, yes. It is highly recommended to use a deck cleaner when prepping your deck for a new coat of deck stain. Also, recommended but not required is the use of a deck brightener before staining your deck. You can then rinse off the deck with your hose.
How do I stain my new deck for the first time?
Stain New Deck Right Away. Apply a wood deck cleaner and thoroughly scrub and or pressure wash lightly. Neutralize with a wood brightener. These two steps will remove the mill glaze and “open” the wood pores. Apply a deck stain that is “thin” in viscosity.
How do you clean a new deck before sealing?
DO repair, wash, and sand your deck before sealing. Then, wash the deck using a power-washer to scrub the surface clean. Allow to dry for 24 hours, then sand the surface with between a 60 to 150 grit sandpaper or sanding disk.
Do I have to sand my deck before staining?
Once dry, these wood fibers can remain raised and may cause splinters. For this reason, light but thoroughly sanding your wood deck is a necessary step before staining or sealing. This crucial step will ensure that your refinishing job gives great results.
Is it better to brush or roll stain on a deck?
You should use a roller brush or sprayer to apply a steady coat of quality stain, such as Olympic Elite stains or Olympic MAXIMUM stains. PRO TIP: Back brushing your stain will help the stain soak into your deck boards, allowing better, long-lasting results.
What happens if you stain a new deck too soon?
Staining too soon can lead to the stain not being absorbed by the wood and result in a patchy and failed upgrade for your deck. Make sure the wood has dropped all of the excess moisture before trying to apply stain. Test to make sure that water is absorbed by the wood which ensures this drying process is done.
How long should you wait before you stain a new deck?
Depending on the wood and drying conditions, you should usually wait 4 to 8 weeks after installation before staining a deck.
How do you seal a brand new deck?
Applying Deck Sealer to a Wood Deck Step 1: Check the forecast. Step 2: Clear the deck. Step 3: Sand (if needed) Step 4: Remove debris. Step 5: Stir sealer. Step 6: Apply sealer. Step 7: Repeat & fine tune. Step 8: Let it dry.
Do you need to apply a sealer after staining a deck?
Most of the time, stains also contain a protective sealant. It’s a good idea, though, to re-seal your deck (or check that it needs to be re-sealed) once a year. Water-based stains can adhere to water or oil-based coatings already present on the wooden surface.
What happens if you don’t sand before staining?
You need a smooth surface with no blemishes because stain will highlight scratches and dings in the wood. Always sand down to clean wood (if you have enough meat left of the wood) before applying any stain. Too fine and the wood won’t be able to accept the stain.
Do you sand or clean deck first?
It is important, to begin with, a power sander and always finish by hand to reach difficult areas. Remember no more than 60 or 80 grit paper. The next step is to clean the wood thoroughly after the sanding. Deck cleaners, also known as deck wash are used to lift dirt and unsightly mildew which accumulates over time.
What grit sandpaper should I use to sand a deck?
Sand the Deck Use 60- or 80- grit sandpaper on the main deck boards, and use 80- or 100-grit on the handrails. After sanding, vacuum the deck thoroughly to ensure that dust does not settle on the new finish.
How many coats of deck stain should I use?
The general rule of thumb is to apply only as much deck stain as the wood can absorb. Typically this will be 2 coats, unless your dealing with extremely dense hardwoods which may only be able to absorb 1 coat of wood stain. Watch this video to see more tips on how many coats of stain to apply.
What happens if you don’t clean deck before staining?
Before you apply stain, make sure the surface is clean (no dust, dirt, wood fibers or grease), dry and free from mildew. When a surface is not clean, stains and other finishes have trouble sticking and may end up peeling.
Should you spray or brush a deck?
The agitation and friction caused by a paint brush will cause the wood to absorb more stain. So if you are spraying or rolling the stain, always back-brush it in with a brush while the stain is still wet; you’ll achieve much better penetration in to the wood.
Should you sand pressure treated wood before staining?
Sanding pressure-treated wood is actually contraindicated because, as Sand & Stain warns, you’ll end up partially removing the protective coating created by the pressure treatment, and the wood will look terrible. Once the wood has dried completely, it’s ready for a coat of transparent or semitransparent stain.
How soon can you stain pressure treated wood?
How long do you have to wait to stain pressure treated wood? Wait until the wood is completely dry. Depending on climate conditions, pressure-treated wood can take anywhere from a few weeks to a few months.
How long should treated wood dry before staining?
If you buy ordinary pressure-treated lumber from a home center, however, you’ll have to wait anywhere from two to three days for the wood to dry sufficiently before you can apply a water-based semitransparent protective stain.
