Table of Contents
There are a few possibilities why your washing machine won’t drain. Your washer may have a clogged drain hose or the pump may be broken. A broken lid switch or belt could also be the culprit. It may even be something as simple as the hose being jammed.
How do you fix a washer that won’t drain?
What to Do When Your Washing Machine Won’t Drain Perform a Master Reset. Unplug your washer for about one minute. Test the Lid Switch Assembly. See if the Drain Hose is Kinked. Check the Drain Hose or Pump for Clogs. Clean out the Coin Trap. Check the Water Level Control. Schedule Washing Machine Repair.
How do I get my washer to drain?
5 Easy Steps to Get Water Out of Your Washer Step 1: Power It Down and Turn Off the Water Supply. Start by powering down your machine. Step 2: See If You Can Drain the Drain Hose. Step 3: Check Out the Drain Pump. Step 4: Drain the Interior Manually If Needed. Step 5: Know When to Call a Professional.
What causes a washing machine not to drain and spin?
If the washer won’t drain or spin, either something is stuck in the washing machine drain hose or pump, or the pump is broken.
How do I know if my washing machine drain hose is clogged?
The surest and most obvious sign that your washing machine’s drain hose is clogged is if you notice that the water in your machine isn’t draining away properly. Many people first notice this after putting their laundry on the spin cycle and realizing that it’s still soaking wet at the end of the timer.
Why does water stay in washing machine drum?
The outer drum is stationary and contains the water, the inner drum rotates and holds the clothes for washing and spinning. The water doesn’t drain out the bottom because the regular drain pipe is above the top of the drum – the water will stay until the drain pump is turned on during the drain and spin cycles.
How do you position a washing machine drain hose?
In order for the drain hose on your Top Load washer to function properly, the drain must be at least 30″ up from the floor and less than 8 feet high. In order for the drain hose on your Front Load washer to function properly, the drain must be at least 24″ up from the floor and less than 8 feet high.
How do I know if my washing machine drain pump is bad?
Put your finger into the drain outlet and feel the impellers if the pump freely turns. One or more of them may be broken. If so, you’ll be able to feel them while you’re turning the pump flywheel with your other hand. You also may see broken pieces of plastic in the bottom of the pump housing.
Can you pour Drano down washing machine drain?
Can I put Drano down my washing machine drain? Yes. Drano or any drain cleaner can be used to unclog your washing machine drain, but make sure you run your washer without a load of laundry before normal use.
How do you manually drain a washing machine?
If not, follow these steps: Step 1: Turn off the power and lay down towels. Step 2: Locate the drain hose at the back of the washing machine. Step 3: Drain the water. Step 1: Turn off the power and lay down towels. Step 2: Locate the drain hose. Step 3: Drain the water. Step 4: Scrub the filter.
Does washer drain need a trap?
When hooking up a new washing machine, some people look for a convenient drain line and simply install a pipe that extends to the washer. The lack of a P-trap exposes the area to sewer fumes and the lack of venting will cause the drain to run sluggishly and overflow. Washers, like all fixtures, need a trap.
Can a washing machine drain into 1 1 2 pipe?
Drain and Trap Requirements A 2-inch drain pipe is required for all washing machines. The former requirement of 1 1/2-inch pipe is not enough to handle the fast drainage of modern washers. As with all plumbing fixtures and appliances, a washing machine drain pipe must also contain a P-trap.
Where is the drain pump located on a washing machine?
The drain pump is located at the bottom of your washing machine, but can be easily accessed in order to replace it if need be. If your washing machine is failing to drain during a wash cycle, it could be that there is a problem with the drain pump.
How much is a pump for a washing machine?
The most important part is a new washer pump. It can cost as little as $10 or as much as $75 or more. However, most homeowners pay between $25-$40 for a new pump.
Why is my Whirlpool washing machine not draining?
If your Whirlpool washer won’t drain, it could be caused by a clogged drain pump, kinked drain hose, faulty lid switch, or a clogged coin trap. To resolve these issues, it is possible to partially disassemble your washer on your own and unclog or replace any problematic areas.
How much does it cost to unclog a washing machine drain?
How much does it cost to unclog a drain? Nationwide, the average cost to clean a clogged drain is $130-$180. This covers both the cost to find the clog and clear the drain. Most plumbing companies will charge a flat rate of $50 – $150 to come out, which also covers the first hour of work.
Can washing machine get clogged?
What causes washing machine clogs? Soap residue, dryer lint debris, and soiled clothing can all lead to clogs in your washing machine.
Where is my washing machine drain trap filter?
Where is the Filter on a Washing Machine? In the front of the unit behind a small hatch. At the end of the drainage hose. Under the cover of your center agitator. Along the top rim of the drum of your washing machine.
