Table of Contents
How do you use a chainsaw for beginners?
If you’re starting the saw between your legs, place the back handle between your thighs and hold the front handle firmly with your left hand. Pull the starter handle with your right hand until the engine fires. Push the choke and pull until the saw starts. Release the chain brake.
What should you not do with a chainsaw?
Don’t Cut With a Dull Blade Cutting with a sharp blade actually extends the life of your chain saw. That’s because a sharp blade pulls itself into the wood, while a dull blade requires lots of downward pressure. That pressure wears out the bar, drive links, clutch sprocket and clutch.
What safety precautions are needed when using a chainsaw?
DO NOT Do not start a chain saw when it is resting against any part of your body. Do not stand directly behind the saw. Do not leave a saw running unattended. Do not carry chain saws while it is running. Avoid contact with the muffler. Serious skin burns may result. Do not cut alone.
How do you stop a chainsaw kickback?
Ways you can avoid chainsaw kickback Read the manual. Make sure the chain brake works before you start. Use low-kickback chains. Use a sharp chain. Be wary when felling tree trunks. Pay attention to the nose of your chainsaw bar.
Is using a chainsaw difficult?
Chainsaws are relatively easy to use once you get used to them but they are dangerous. They will cut flesh and bone as if it is not there.
Should you wear gloves with chainsaw?
Always wear protective gloves when using a chainsaw. Chainsaw gloves are just one component of what you should wear when cutting wood. The other essentials are: Chainsaw chaps, protective head gear and a cut-resistant jacket.
What is the most common chainsaw injury?
The most common hazards associated with chainsaws are injuries caused by kickback, pushback, and pull-in. Kickback is the most common and poses the greatest hazard. Kickback occurs when the rotating chain is stopped suddenly by contact with a more solid area throwing the saw rapidly backward toward the operator.
Can you cut wet wood with a chainsaw?
Yes, you can use a chainsaw to cut wet wood.
How does chainsaw kickback happen?
There are two circumstances that can cause kickback when using a chain saw. The first occurs when the moving chain at the tip or the nose of the guide bar strikes an object. The second situation is when the wood closes in, pinching the saw chain in the middle of the cut.
What PPE is required to operate a chainsaw?
The Occupational Safety and Health Administration (OSHA) requires that saw operators wear head protection, eye protection, hearing protection, chainsaw chaps or pants, and suitable footwear.
How long should you warm up a chainsaw?
Chainsaw warm-up is briefly starting the machine and letting the engine/motor run for a few seconds. Whether you have one from Husqvarna, STIHL, Craftsman, or Echo, every woodworker would want to have a great sawing day with their tool.
How do I stop my chainsaw from pinching?
To stop your chainsaw from getting stuck, make a cut on top of the log or tree that’s preferably one-third of the log’s diameter. Use your chainsaw to cut from the underside until you meet the initial top cut. Always stand on the side when cross-cutting to prevent injury.
Should you run a chainsaw at full throttle?
Engine Protection Generally, two-stroke chainsaw engines are built to conveniently run at full throttle without an engine breakdown. Therefore, running at any throttle speed below the full throttle is not advised.
How often should you change the bar on a chainsaw?
If you are looking for a general idea for how often you should replace a chainsaw bar, a rule of thumb is to replace the bar of your chainsaw once after you have gone through three chains on the same bar.
Do you need chainsaw trousers?
The importance of wearing safety trousers Chainsaw protective trousers have to comply with the EN381-5 standards. It is essential to wear trousers that are made of a sturdy and durable material that has a certain amount of stretch. This material needs to be resistant to chainsaw cuts as well as comfortable.
What is the safest way to cut down a tree?
Whenever possible, stand on the uphill side of the tree. Work from the left side of the trunk (as you face toward the top of the tree). This allows the safest and most efficient use of the chain saw because you can rest the side or bottom of the saw on the trunk and slice off the branches with a pivoting motion.
Which chainsaw will cut a thick piece of wood faster?
Power. Gas chainsaws operate at greater speeds and have longer run times than electric chainsaws, making them ideal for cutting larger trees and branches or bigger jobs involving multiple trees. Since they have more power, they can drive long 20-inch bars, making them suitable for bringing down larger trees.
What size chainsaw do I need to cut firewood?
Many homeowners find that a 14- to 16-inch chainsaw is a good length for them. That’s long enough to limb-up trees, cut down small trees, and cut most firewood, but it’s also short enough that it’s easy to control the saw.
