Table of Contents
How do I know if my trailer bearings need replacing?
Jack up the trailer and secure it on adequate capacity jack stands. Check wheels for side-to-side looseness – There should be a very slight amount of play in the wheel, typically 1/8-inch or less. If the wheels are loose or spin with a wobble, the bearings must be serviced or replaced.
How do I know if my trailer bearings need grease?
Keep your hand on the wheel and spin it. If you feel any motion that is not smooth, hear any noises, or if the wheel does not spin freely, the wheel bearing is defective or needs lubrication.
How do I check my trailer bearings?
The simple way to identify your bearings is from the code printed on the bearing itself. Above: If possible, identify your bearing by the number on the cone. A bearing KIT will include all parts shown for one wheel.
How often should you check trailer wheel bearings?
The trailer type, wheel size, and average load weight are some of the factors that affect the wheel bearing maintenance frequencies. RV’s wheel bearings should be inspected and greasing at least every 10,000 miles, according to some manufacturers. Every 2,000 miles, the boat trailers need to be re-packed.
How do you diagnose wheel bearings?
What are the symptoms of bad wheel bearings A humming, rumbling or growling noise that increases with acceleration or as the vehicle turns. A loud constant whining or grinding noise when the vehicle is in motion. Clunking noises when driving over uneven road surfaces.
What happens when trailer bearings fail?
Improper maintenance of your wheel bearings isn’t just a risk to yourself; not properly servicing your wheel bearings can compromise the safety of the passengers in the tow vehicle and those that share the road with you. Failure to maintain axle bearings can cause your wheels to fall off while the trailer is in motion.
Can you over grease trailer wheel bearings?
They keep grease packed into the hub. munchy wrote: More grease is never the right answer. Overgreasing can actually cause the rollers/balls to slide over the bearing surface rather than roll over them.
Can you over grease trailer bearings?
There’s no such thing as too much grease for bearings! You would not pack grease in the hub otherwise and not in the drum since the brakes would not be able to grab with grease in the hub. Grease caps, dust caps, and bearing protectors have to be installed right to avoid losing them.
Should I fill my trailer hub with grease?
1 and 2), pump a ring of grease into the entire circumference of the wheel hub and coat the hub cap inner wall. The housing should only be half full of grease. Too much grease causes churning and higher temperatures. Semi-fluid grease must be used with a vented hub cap.
How much does it cost to repack trailer bearings?
Trailers tend to be cheaper to repack professionally (think $100-$200), but don’t underestimate the power of the upsells a mechanic might try to give you. If you’re serious about cash, you can likely save a few bucks by repacking your bearings yourself.
How often should I grease my bearing buddies?
Every 3,000 to 3500 miles or annually, whichever comes first. Manufacturers recommend to remove old contaminated grease from the hub and repack with new grease instead of just adding more.
How do you tell if a wheel bearing is going bad?
Top Warning Signs Your Wheel Bearings Need Replacement Humming Noise. The most easily identifiable and common symptom of bad wheel bearings is audible. Squealing, Growling. Clicking Sound. Wheel Wobble. ABS Failure. Uneven Tire Wear. Vehicle Pulls to One Side. Steering Wheel Vibration.
How long should trailer bearings last?
Expert Reply: We recommended to repack the wheel bearings on your trailer every 12 months or 12,000 miles. There is not a specific guideline as far as actually replacing the bearings. When repacking them with grease, you will also just want to check for any damage or wear and replace anything if needed.
What causes trailer bearings to go bad?
Failure is usually caused by either lack of lubrication (which causes excessive heat), overloading (which causes lack of lubrication because of the excess weight), the axle nut is too tight (which, again, causes lack of lubrication) or the axle nut is too loose (which will allow for unnecessary movement causing bearing.
How often should you grease utility trailer wheel bearings?
Proper lubrication helps maintain functionality and reliability of your trailer’s axle(s). Bearings should be lubricated approximately every 12 months or 12,000 miles unless otherwise specified by the axle manufacturer.
Do I grease a tow ball?
You do not need to grease your trailer hitch ball. That is entirely up to you. However, greasing it is recommended. Greasing will help ensure that the trailer hitch ball keeps its structural integrity, and it will help prevent it from squeaking.
Are bearing buddies a good idea?
Bearing Buddies are a great way to keep grease in a trailer hub. I recommend them as long as you are aware that it’s very easy to put too much grease in a hub with these which will blow out the seal. They have no problem being used on longer road trips so the would work well for you.
How long does it take to repack trailer bearings?
How many trailers have you seen on the side of the road this year with one wheel propped up? Don’t let it happen to you. If you haven’t checked your wheel bearings lately, read this article. You can complete this simple task in about an hour and save yourself a big repair bill.
