Table of Contents
How do you change a ballast in a fluorescent light fixture?
Instructions Remove the Cover. Remove the lens, or diffuser cover, from the fixture. Remove the Fluorescent Tubes. Remove the light bulbs (fluorescent tubes). Remove the Cover Plate. Disconnect the Ballast Wires. Remove the Ballast. Prepare the Wires. Mount the New Ballast. Dispose of the Old Ballast.
How hard is it to replace a ballast in a fluorescent light?
The ballast takes in electricity and then regulates current to the bulbs. You can get a new ballast at a hardware store or home center and install it in about 10 minutes. However, buying a ballast can be expensive, so consider pricing a brand-new fixture for comparison.
What are the signs of a bad ballast?
2. Look for warning signs that the ballast is failing. Buzzing. If you hear a strange sound coming from your bulbs or light fixture, like a buzzing or humming noise, that’s often a sign your ballast is going. Dimming or flickering. No lights at all. Changing colors. Swollen casing. Burn marks. Water damage. Leaking oil.
How can you tell if a fluorescent light ballast is bad?
If your fluorescent lighting is displaying any of the signs below, it could be a symptom of a bad ballast: Flickering. Buzzing. Delayed start. Low output. Inconsistent lighting levels. Switch to an electronic ballast, keep lamp. Switch to an electronic ballast, switch to a T8 fluorescent.
Do I need an electrician to replace a ballast?
Yes. In fact, you really need a locking device to replace the ballast. – An electrician replaces the ballast on a fluorescent lamp. He uses a switch on the wall to turn off the fluorescent light.
How is a ballast wired?
Usually hidden from view, the ballast is installed inside an overhead fluorescent light unit, and is covered by a shield or plate. The ballast has a hot and neutral wire at one end to receive power, and two blue wires a red one at the other end to supply power to the lights.
Will a bad ballast burn out bulbs?
The ballast itself can go bad, which causes lights to flicker or even appear to be burnt out, when in fact they aren’t. They require maintenance and energy to power, on top of the power used to light the fluorescent bulb. They are a large part of the equation when using fluorescent lamps.
Why are my fluorescent lights flickering?
If your fluorescent bulbs flicker, most likely the problem is with the bulb itself. If the bulb is very dark on either end, it may be defective and burned out. The best way to test the functionality of a bulb is to put it into a fixture you know works. Flickering fluorescent lights can also be a result of temperature.
What happens when a ballast goes bad?
But there is a good chance your ballast could be the cause of your lighting woes if your lights are dim, buzzing, changing colors, or flickering rapidly. You should check all parts of the fixture, including the bulbs. If the bulbs fail to light up, then 9 out of 10 times the ballast is culprit.
Why does my fluorescent light work sometimes?
If a fluorescent tube blinks on and off-a slower and more distinct process than flickering-the fault may lie in loose wiring or in another component, called the ballast. The ballast is almost always to blame if the fixture hums during operation.
Which ballast do I need?
By selecting a ballast with an ideal ballast factor, you can optimize the light output of your fluorescent lighting system and maximize your energy savings. To estimate your total system lumens, multiply the rated lumens of your lamp by the ballast factor. For example, 3200 lumens x 0.77 BF = 2464 total system lumens.
How do I know if my ballast is T8 or T12?
If no markings are available, the size in diameter of the tube is the easiest way to determine the type you have installed. T8 tubes are 1-inch in diameter and T12 tubes are 1 1/2 -inch.
Why do ballasts hum?
A loose magnetic ballast can be the cause of ballast hum. Check that ballast mounting screws are tight. If the hum is louder than usual the ballast may need to be replaced as ballasts can wear out over time. If you do choose to replace a magnetic ballast, consider replacing with an electronic one.
How long does fluorescent ballast last?
According to the Certified Ballast Manufacturers Association, the average magnetic ballast lasts about 75,000 hours, or 12 to 15 years with normal use. The optimum economic life of a fluorescent lighting system with magnetic ballasts is usually about 15 years.
Why do fluorescent lights not turn on sometimes?
If you find your fluorescent light won’t turn on sometimes, there could be a variety of reasons why. It could be as simple as needing to replace the bulb or plug the light itself in; or, it could be something more serious, such as a blown fuse or a damaged/dying starter.
Is it the starter or the ballast?
In older fluorescent fixtures, the ballast, or choke, is a transformer that limits the current flowing into the tube, while the starter provides the high voltage needed to excite the tube when it is turned on.
Is it cheaper to replace ballast or fixture?
A replacement ballast costs about $10-25 depending on capacity and brand. The bite is that an electrician trip charge (which includes 30 or 60 minutes work) is going to be $75-150 probably – for about 5 minutes work on each light fixture.
