Table of Contents
Do you drywall ceiling first?
Hanging Drywall From the Top Down Hang drywall on the ceiling first, then the walls. Check the ceiling for bowed joists using a 4-ft. are of no concern, but seriously warped framing will require you to use drywall shims–long strips of 1/8- or 1/16-in.
Which way do you run ceiling drywall?
On commercial jobs, fire codes often require seams to fall on the entire length of the framing, so the drywall must be hung vertically. However, on residential jobs, the drywall on the walls is typically hung horizontally. For walls 9 feet high or shorter, hanging the drywall horizontally has a number of benefits.
How many screws do you put in sheetrock on the ceiling?
In standard home construction, about 28 screws are needed to properly attach a 4-by-8-foot piece of drywall. That’s if the panel is going on a wall. If it’s going on a ceiling, it’ll take about 36 screws.
How thick should sheetrock be for a ceiling?
5/8-Inch-Thick Drywall When installed on ceilings, 5/8-inch-thick panels are less susceptible to sagging between the joists than 1/2-inch panels. Adding popcorn texture or another type of heavy surfacing material can add to the weight problem, making 5/8-inch drywall a better choice for ceilings.
How much gap should be between sheets of drywall?
Always leave a 1/2-inch gap at the floor. This allows for floor and wall expansion without cracking the drywall. It also helps prevents moisture wicking if the floor floods.
Do you stagger drywall seams on ceiling?
It’s not necessary to stagger seams on ceiling drywall. However, because these joints are relatively difficult to finish – and tend to be noticeable in the finished product – it’s a good idea to stagger the drywall panels to make the joints less visible.
Do drywall seams have to be on a stud?
Drywall Is Not on a Stud All edges of all sheets of drywall must land on a solid surface such as a stud. A hanging drywall edge may work in the short-term, but in the long-term it can result in cracks and other serious wall issues. Sometimes, the drywall does not horizontally reach a stud.
What is the screw pattern for drywall?
Drywall screws pattern A general rule of thumb is that drywall screws should be installed every 12 inches. This means that when using 48 inch wide sheets, you will have 5 screws in each stud when the sheets are hung perpendicular to the framing; two on the edges and 3 in the field.
Why is it important to install the drywall on the ceiling before the walls?
Doing the ceiling first means you can lift the wall sheets to make a tight joint. By contrast if you do the walls first you would have to sculpt every edge to make it seat tightly, and/or end up with lots of voids to fill before you tape.
Why do you hang drywall from the top down?
When hanging drywall, always hang the ceiling first. This is the hardest drywall to hang, so get a partner and go slow. Large cracks due to misaligned sheets are hard to repair because the extra mud required to fill them will constantly fall out and drop to the floor (or worse, down the back of your neck!).
Is it better to nail or screw drywall?
Drywall nails are better and easier for the DIYer. Screws are a pain and do not grab as much surface area as nails. Nails, when driven in drywall are countersunk slightly and give a much larger area for drywall. Screws are the cheap way for pros to go and they will always take the cheap over the better.
Where do you start sheetrock on a ceiling?
Installation starts in one corner of the ceiling with the length of the drywall panels running perpendicular to the direction of the ceiling joists. If the room is wider than the length of the panels, measure and cut additional panels so the panels meet on the center of a joist.
How long should drywall screws be for 1/2 inch drywall?
When working with 1/2-inch drywall panels, use 1-1/4 or 1-3/8-inch nails or screws. When working with 5/8-inch drywall panels, use 1-3/8-inch or 1-5/8-inch screws. To properly secure drywall, the right number of drywall fasteners should be used.
Should I use #6 or #8 drywall screws?
Drywall only, please: Don’t use drywall screws for sub-floors, tile backing or other non-drywall applications. These denser materials can break the smaller #6 screw during installation. Use a #8 or larger for these jobs.
How many screws go into a sheet of drywall?
How Many Screws Per Sheet of Drywall. Use about 32 drywall screws per sheet of 4-foot by 8-foot drywall installed horizontally on a wall. This total is comprised of four screws on the five middle studs and six screws on each of the two sides.
How long should drywall screws be for ceiling?
Screws that measure 1-1/4 inch in length are appropriate for sheets of drywall that are 3/8, 1/2 or 5/8 of an inch thick, while screws that measure 1-3/8 inches are meant for sheets of drywall up to ¾ of an inch thick.
