Table of Contents
Ensure your furnace filters are clean: Your furnace won’t start up if it does not get enough airflow. Check your pilot light: If you have a gas furnace and gas supply is stopped your pilot light will go out. Check your blower motor: If the blower motor is not working then your furnace won’t pump out warm air.
What causes a furnace not to kick on?
The Pilot Light (Faulty Ignition Sensor) The pilot light or ignition sensor is usually the most common issue when your furnace will not ignite. This is typically the problem if you can hear your furnace click on but it does not fire up. If the sensor or ignitor is dirty, it will need to be cleaned.
How do I get my furnace to kick on?
If the pilot light on your furnace is out, the furnace will not turn on. You can try lighting the pilot. If it stays lit, your furnace will kick on. If it does not, there could be a problem with the assembly or the sensor, and a professional would need to come in and fix it.
Why is my furnace not responding to thermostat?
Loose connections, frayed wires, and aged wires all can cause your thermostat to eventually lose its connection to your A/C and heating system. Inspect your wiring thoroughly, making sure the connections are tight, and replace any wires as deemed necessary by you or an HVAC professional.
How do I reset my furnace?
How to Reset an Electric Furnace First, turn off the power supply to the furnace by turning off the breaker in the circuit box. Locate the reset button on the furnace and press it to reset the furnace. If the button is popped up, press it down. Return the cover to the blower compartment and turn the power on.
How do I know if my thermostat is broken?
7 Ways to Tell Your Thermostat Is Broken Thermostat Has No Power. AC or Furnace Won’t Turn On. Heater or AC Won’t Turn Off. Thermostat Doesn’t Match Room Temperature. Thermostat Doesn’t Respond. Short Cycling. Thermostat Forgets Programmed Settings.
How long does it take for furnace to reset?
Either way, restarting a furnace is a relatively simple task that takes no longer than 10 minutes to complete. Follow these steps to reset your gas furnace: Turn the circuit breaker off and switch the furnace power button off too. Never touch the breaker with wet hands and use only one hand to do it.
Is there a pilot light for furnace?
What is the Pilot Light For? Older furnaces that run on natural gas are usually equipped with a pilot light. The pilot light is a small, blue flame that is used to ignite the natural gas being pumped into the main burner.
Do all furnace blower motors have a reset button?
All furnaces are equipped with a reset button. They are generally red or yellow and are located inside the blower compartment. The reset button is a safety feature that will shut down the furnace when a problem is detected, often a hot or overheating furnace, before it trips the circuit breaker.
How do you tell if you need a new thermostat in your house?
Signs You Need a New Thermostat Heating or cooling system will not turn off or on. The temperature reading is incorrect. Recent spike in your energy bill. Frequent temperature fluctuations. Thermostat is 10 years old or older.
How can I tell if I need a new thermostat?
7 Signs You Need to Replace Your Thermostat Your HVAC Keeps Turning On or Off. Faulty Thermostat Readings. Suspiciously High Energy Bills. Constant Temperature Shifts. Thermostat Is Too Old. Thermostat Fails to Respond to Changed Settings. Your HVAC System Short Cycles.
How do you test a furnace thermostat?
How to Test Your Furnace Thermostat Step 1: Reset the thermostat lower or higher. Step 2: Make sure the thermostat is ON. Step 3: Check the wiring. Step 4: Turn breaker back on. Step 5: Reexamine wires. Step 6: Wrap wires together.
How long should it take for a furnace blower to turn on?
In normal operation, your furnace blower fan should come on 1.5 to 3 minutes after your thermostat calls for heat and should turn off several minutes after the heating cycle ends.
How do you reset a furnace blower motor?
How to Find and Reset your Furnace Motor Blower Step 1: Turn off the power to the furnace. Step 2: Remove the blower compartment cover. Step 3: Make sure the blower is completely cooled off. Step 4: Locate the reset button. Step 5: Press the button in (assuming that this is your issue and that the button has popped).
How do I know if my furnace ignitor is bad?
Your furnace won’t run: The most obvious sign that your ignitor is bad is that it won’t ignite, and this generally manifests itself in your furnace failing to run when you activate it. One word of caution, though: this can also be caused by other issues, some of which are electrical.
How do you know if your furnace pilot light is out?
How to Tell If the Pilot Light Is Out Locate the front cover panel on your furnace. It should be a little door that’s easily visible. If your pilot light is on, it should be easy to see – your eyes will be drawn to the little flame. If you don’t see a flame, your pilot light is out. If there is a flame, check the color.
What can cause a blower motor to stop working?
In most cases, a blower motor resistor fails due to corrosion or overheating. Sometimes, the mechanical resistance to the motor rotation causes an excessive electric current that can overheat and prematurely damage the blower motor resistor.
How much does it cost to replace a blower motor on a furnace?
On average nationwide, a furnace blower motor replacement costs $400-$600, including parts and labor. A single-speed blower motor costs around $450 to replace while a variable-speed motor costs $600+.
