Table of Contents
How do you cut down a tree without a pinching chainsaw?
To stop your chainsaw from getting stuck, make a cut on top of the log or tree that’s preferably one-third of the log’s diameter. Use your chainsaw to cut from the underside until you meet the initial top cut. Always stand on the side when cross-cutting to prevent injury.
What should you not do with a chainsaw?
Don’t Cut With Improper Blade Tension A overly loose or tight chain also wears out the drive sprocket and causes rapid chain and bar wear. To determine if your chain is properly tensioned, pull up on the chain. The drive links should still be in the bar groove. If the links come out of the bar, the chain is too loose.
What is the most common chainsaw injury?
The most common hazards associated with chainsaws are injuries caused by kickback, pushback, and pull-in. Kickback is the most common and poses the greatest hazard. Kickback occurs when the rotating chain is stopped suddenly by contact with a more solid area throwing the saw rapidly backward toward the operator.
Which way will a tree fall in a storm?
A tree will most likely fall in the direction of the lean.
How do I cut down a large tree around my house?
When cutting large branches that may fall and damage your house, tie a rope around the branch. Then, wrap the other end around another tree trunk, at ground level. With assistance from 1 or more other workers, unwrap the rope around the tree trunk and slowly lower the large branch to the ground.
Which chainsaw will cut a thick piece of wood faster?
Power. Gas chainsaws operate at greater speeds and have longer run times than electric chainsaws, making them ideal for cutting larger trees and branches or bigger jobs involving multiple trees. Since they have more power, they can drive long 20-inch bars, making them suitable for bringing down larger trees.
How do you cut a large tree in sections?
Make your first cut (the bottom of the top section) at a 70-degree angle downwards on the side of the section you want to fall, cutting into about one-third of the trunk. Next, lower your chainsaw and cut upwards at a 20-degree angle until you meet the end of the first cut, making a right triangle.
How do you safely fell a dead tree?
Do not intersect the back cut and the undercut. Instead, leave a bit of uncut wood between the two cuts. Then, as soon as possible, insert a falling wedge into the back cut. The wedge will help ease the tree in the right direction and can also help you adjust if it starts leaning the wrong way.
What does bucking a tree mean?
Felling involves cutting the standing tree and dropping it in the place you want it. Limbing is the removal of the branches from either standing or downed trees. Bucking is the process of cutting the downed tree into appropriate lengths.
Why does my chainsaw jump when cutting?
Too much slack in your chain can cause the saw blades to jump the bar. This is commonly referred to as throwing the chain. Place a dime between the chain and bar, then increase the tension until the chain is snug against the dime. Remove the dime and you’re ready to cut.
How do you cut a log under tension?
A felled tree will usually have saw-pinching areas where the top of the log is under compression and the bottom is under tension. If you have access to the top and bottom of the log, you can handle this one of two ways. Make a cut directly down from the top and then finish by cutting up from the bottom.
Can you use a chainsaw to cut tree roots?
Both manual and chain saws can cut through roots of any size. Use a shovel to dig out the area around large roots, as the soil will clog the space between the saw teeth and make it harder to cut.
How often should you change the bar on a chainsaw?
If you are looking for a general idea for how often you should replace a chainsaw bar, a rule of thumb is to replace the bar of your chainsaw once after you have gone through three chains on the same bar.
Should you wear gloves with chainsaw?
Always wear protective gloves when using a chainsaw. Chainsaw gloves are just one component of what you should wear when cutting wood. The other essentials are: Chainsaw chaps, protective head gear and a cut-resistant jacket.
How long should chainsaw blade last?
The chain should last many years; 5-6 years should be no problem. However, if the chainsaw chain is used properly and taken care of, it can last way longer.
How do I stop my chainsaw kickback?
Stand to side of the cutting path of the chain saw. Position yourself so that you are not near the cutting attachment when the chain saw is running. Know where the bar tip is at all times. Install a safety tip that covers the nose of the guide bar on the saw to prevent contact with the kickback zone.
How many people are killed by chainsaws every year?
They can also quickly cause severe injury or death. According to the Centers for Disease Control and Prevention (CDC), approximately 36,000 people are injured by chainsaws annually.
