Table of Contents
What is the best way to apply Wipe-On Poly?
Apply a liberal amount of Wipe-On Poly to a clean, soft, lint-free cloth and rub it into the wood. Let dry 2-3 hours. Then lightly sand entire surface with fine sandpaper (220 grit) to ensure an even finish and proper adhesion. Remove all dust.
How do I get a smooth finish with Wipe-On Poly?
Wash it first with dish soap and water, then lightly sand the old finish with 220-grit sandpaper. Vacuum off the dust, then apply the finish as usual. Apply at least two coats to achieve an even sheen.
How do you wipe on polyurethane?
A margarine or cottage cheese tub is just right for wipe-on. Dip your rag into the finish, squeeze out the excess and wipe on. With the lid in place, the poly will remain fresh for a couple days. After a few days, the solvent will begin to degrade the plastic, so don’t use plastic for long-term storage.
What kind of rag do you use for Wipe-On Poly?
Here’s what I use when I apply wipe on poly to a finished piece of furniture: Minwax clear gloss wipe on poly. Minwax satin finish wipe on poly. White, lint-free cotton rags.
Can you apply polyurethane with a rag?
Polyurethane is so durable and water-resistant, it has largely replaced shellac and varnish as a wood finish. Originally, it had to be brushed on, but different formulations mean it can now be applied as a spray or by wiping it on with a rag.
Do you wipe off polyurethane?
Wipe the polyurethane varnish — directly from the can — onto the wooden surface, using a piece of cloth. Apply it in the same direction as the woodgrain to avoid streaks, then wipe off the excess with a clean cloth. Wipe off less varnish on the wood’s surface for a thicker finish.
Does Wipe-On Poly penetrate wood?
Yes, you can use wipe on poly over stain. Wipe on poly is an excellent paint to protect your unfinished wood. But be sure to allow the stained wood to dry thoroughly before top coating with the wipe on poly.
Should I sand after first coat of polyurethane?
Sand the dried and cured first coat of polyurethane no sooner than 24 hours after applying it. Use a very fine-grit abrasive, sanding with the grain of the wood.
How do you make a water based wipe on polyurethane?
For water borne polyurethane I use tap water or distilled water (never well water) as my thinning agent. To make your own wipe on polyurethane I recommend thinning to 50/50. One part polyurethane to one part thinning agent.
How do you finish the last coat of polyurethane?
How to Dry Sand the Last Coat of Polyurethane Step 1: Vacuum the Surface. Step 2: Wipe the Surface with Mineral Spirits or Water* Step 3: Let the Water Evaporate. Step 4: Start Sanding. Step 5: Clean the Surface. Step 6: Use a Finer grit.
Can you wipe on Minwax Fast Drying polyurethane?
Just keep adding to the ball and keep wiping. Twist the cover to squeeze the ball and let more poly out. I also always sand with 320 grits between coats. Don’t over-wipe it, keep a good wet coat on it and let it flow out.
Why does my polyurethane have streaks?
Bruce Wedlock replies: Brush streaks come from the finish not smoothing out after the application. Viscous finishes like typical oil varnishes don’t flow easily, so brush marks can result. One solution is to thin the finish so it flows evenly before it tacks up.
Can you apply Minwax polyurethane with a rag?
Ease of application: Some Minwax® clear finishes can be easily applied with a cloth—no need to worry about drips or brush marks. Some dry very quickly and can be cleaned up with soap and water, while others require mineral spirits.
How do you get brush marks out of polyurethane?
How to Remove Brush Marks From a Polyurethane Finish Sand down the brush marks lightly with the fine-grit sandpaper. Brush the sanded area off with a soft cloth to remove all traces of dirt and grit from the sanding. Apply the polyurethane finish lightly to the brush, making sure to wipe off any extra.
How long does it take for Wipe-On Poly to cure?
Wipe-On Poly will dry to the touch in 2-4 hours, to handle in 8-12 hours and can be recoated in 4-6 hours. Full cure will be achieved in 24 hours. Use paint thinner or mineral spirits.
Should I apply polyurethane with a rag or brush?
Apply the first coat of polyurethane using the best technique for the surface. Brush flat surfaces with a thin coat using a bristle brush. Wipe contoured surfaces with a clean cloth, going with the grain. Brushing a rounded, contoured or vertical surface is more likely to create drips.
Can I use a foam brush to apply polyurethane?
Yes, it is OK to use a foam brush to apply polyurethane. However, it isn’t the best choice for larger projects because the foam doesn’t spread the polyurethane as well as a synthetic or natural brush. Use a foam brush to apply polyurethane to smaller projects, like finishing a birdhouse.
How do you apply water-based polyurethane with a rag?
Applying a Water-Based Polyurethane Apply a very thin coat of polyurethane with a fine brush, foam pad, or cloth. Work with the grain, and avoid applying too much polyurethane to avoid raising the grain. The initial coat should be dry within a couple of hours, and you can then apply a second coat.
